This study evaluated nanocellulose derived from discarded palm leaves for its ability to remove cobalt ions from industrial wastewater. The process involved extracting cellulose nanocrystals (CNCs) from date palm leaves through a series of repeated chemical treatments. The study examined the adsorption rates of cobalt ions under various conditions using different techniques. Two equilibrium models, the Langmuir and Freundlich models, were employed, and the Langmuir model was found to be consistent with the experimental data. The maximum amount of cobalt ions adsorbed at room temperature was 5.98 mg/g. Furthermore, several kinetic models were used to gain insight into the adsorption mechanism, including the pseudo-first-order, pseudo-second-order, Elovich, and intraparticle diffusion models. The pseudo-second-order model provided an accurate description of the adsorption process, while the Elovich equation suggested a chemical reaction between cobalt ions and nanocellulose, involving multiple chemical reactions and mass-transfer processes. Kinetic parameters were critical in interpreting the results, and the study’s findings were in agreement with the pseudo-second-order and intraparticle models, indicating general chemical reactions and diffusion resistance.

High-performance polybenzimidazole (PBI) hollow-fiber membranes (HFMs) were fabricated through a continuous dry-jet wet spinning process at SRI International. By adjusting the spinning air gap from 4″ (10.2 cm) to 0.5″ (1.3 cm), the HFM pore sizes were enlarged dramatically without any significant change of the fiber dimensional size and barrier layer thickness. When fabricated with an air gap of 2.5″ (6.4 cm) and a surface modified by NaClO solution, the PBI HFM performance was comparable to that of a commercial reverse osmosis (RO) HFM product from Toyobo in terms of salt (NaCl) rejection and water permeability. The PBI RO HFM was positively surface charged in acidic conditions (pH < 7), which enhanced salt rejection via the Donnan effect. With an air gap of 1.5″ (3.8 cm), the PBI HFM rejected MgSO₄ and Na₂SO₄ above 95%, a result that compares favorably with that achieved by nanofiltration. In addition, the PBI HFM has a defect-free structure with an ultra-thin barrier layer and porous sublayer. We believe PBI HFMs are ideal for water purification and can be readily commercialized.

In this study, a red clay/nano-activated carbon membrane was investigated for the removal of oil from industrial wastewater. The sintering temperature was minimized using CaF₂ powder as a binder. The fabricated membrane was characterized by its mechanical properties, average pore size, and hydrophilicity. A contact angle of 67.3° and membrane spore size of 95.46 nm were obtained. The prepared membrane was tested by a cross-flow filtration process using an oil-water emulsion, and showed a promising permeate flux and oil rejection results. During the separation of oil from water, the flux increased from 191.38 to 284.99 L/m² on increasing the applied pressure from 3 to 6 bar. In addition, high water permeability was obtained for the fabricated membrane at low operating pressure. However, the membrane flux decreased from 490.28 to 367.32 L/m²·h due to oil deposition on the membrane surface; regardless, the maximum oil rejection was 99.96% at an oil concentration of 80 NTU and a pressure of 5 bar. The fabricated membrane was negatively charged, as were the oil droplets, thereby facilitating membrane purification through backwashing. The obtained ceramic membrane functioned well as a hydrophilic membrane and showed potential for use in oil wastewater treatment.

In this study, a method for fabricating tubular ceramic membranes via extrusion using economical and locally available bentonite–silica sand and waste palm leaves was developed as a tool for conducting the necessary task of purifying water polluted with oil and suspended solid materials produced via various industrial processes. The developed tubular ceramic membranes were found to be highly efficient at separating the pollutants from water. The properties of the fabricated membrane were evaluated via mechanical testing, pore size distribution analysis, and contact angle measurements. The water contact angle of the fabricated membrane was determined to be 55.5°, which indicates that the membrane surface is hydrophilic, and the average pore size was found to be 66 nm. The membrane was found to demonstrate excellent corrosion resistance under acidic as well as basic conditions, with weight losses of less than 1% in each case. The membrane surface was found to be negatively charged and it could strongly repulse the negatively charged fine bentonite particles and oil droplets suspended in the water, thereby enabling facile purification through backwashing. The obtained ceramic membranes with desirable hydrophilic properties can thus serve as good candidates for use in ultrafiltration processes.

Environmental risks can arise from the existence of heavy metals in wastewater and their land disposal. To address this concern, a mathematical technique is introduced in this article that enables the anticipation of breakthrough curves and the imitation of copper and nickel ion separation onto nanocellulose in a fixed-bed system. The mathematical model is based on mass balances for copper and nickel and partial differential equations for pore diffusion in a fixed bed. The study evaluates the impact of experimental parameters such as bed height and initial concentration on the shape of the breakthrough curves. At 20 °C, the maximum adsorption capacities for copper and nickel ions on nanocellulose were 5.7 mg/g and 5 mg/g, respectively. The breakthrough point decreased with increasing solution concentration at higher bed heights, while at an initial concentration of 20 mg/L, the breakthrough point increased with bed height. The fixed-bed pore diffusion model showed excellent agreement with the experimental data. The use of this mathematical approach can help alleviate the environmental hazards that arise from the presence of heavy metals in wastewater. The study highlights the potential of nanocellulose as a material for membrane technology, which can effectively address these risks.