This paper investigates the effect of alteration on the physicomechanical properties of igneous rocks used as aggregates, from various areas from Greece. The studied lithologies include serpentinized dunites, serpentinized harzburgites, serpentinized lherzolites, metamorphic gabbros, diabases, dacites and andesites. Quantitative petrographic analysis shows that the tested samples display various percentages of secondary phyllosilicate minerals. Mineral quantification of the studied rock samples was performed by using the Rietveld method on X-ray diffraction patterns. The samples were also tested to assign moisture content (w (%)), total porosity (n_t (%)), uniaxial compressive strength (UCS (MPa)) and Los Angeles abrasion test (LA (%)). The influence of secondary phyllosilicate minerals on the physicomechanical behavior of the tested samples was determined using regression analysis and their derived equations. Regression analysis shows a positive relationship between the percentage of the phyllosilicate minerals of the rocks and the moisture content as well as with the total porosity values. In mafic and ultramafic rock samples, the relationships between the secondary phyllosilicate minerals and their physicomechanical properties have shown that the total amount of the secondary phyllosilicate minerals results negatively on their physicomechanical properties. On the other hand, the low percentage of phyllosilicate minerals in volcanic rocks can’t be able to define their engineering properties.

Beachrocks are a window to the past environmental, geological, sedimentological and morphological conditions that were dominant in the coastal zone during their formation. Furthermore, beachrocks have the ability to reduce coastal erosion impact on sandy beaches. This study focuses on the beachrock formation mechanism through the comparison of cement characteristics, mineral chemistry and sedimentology of beachrock occurrences from two different geological and geographical localities: Diolkos, Corinth, Greece and Sumuide, Okinawa, Japan. In addition, in order to investigate a potential soft engineering method to protect coasts from erosion, artificial beachrock samples were created in vitro using sand samples and ureolytic bacteria from both areas under accelerating conditions. For Okinawa artificial beachrock experiments, the bacteria Pararhodobacter sp. was used, and for Diolkos, it was the bacteria Micrococcus yunnainensis sp. For the natural beachrocks, a multi-analytical approach was accomplished with the use of microscopic investigation, a scanning electron microscope, energy-dispersive X-ray spectroscopy, X-ray diffraction and X-ray fluorescence. Correlations were made between natural and artificial beachrocks. Results have shown that Diolkos beachrock was formed in the upper part of the intertidal zone, consisting of detrital material originating from the local bedrock, while Sumuide beachrock formed in the low intertidal–upper subtidal zone, consisting of coral sand and foraminifera fragments. For the artificial beachrocks, three samples were created using the microbial-induced carbonate precipitation (MICP) method, one from Diolkos (Corinth, Greece) and two from Sumuide (Okinawa, Japan). Diolkos artificial beachrock was better consolidated in comparison to Sumuide. Our investigation has shown that bacterial density was the key factor for the creation of the artificial beachrocks, while the samples’ granulometry played a secondary role in the process. The laboratory artificial beachrocks show encouraging results for a new soft engineering method to encounter beach erosion while keeping an ecofriendly character by saving energy, material resources and gas emissions. Artificial beachrocks can share the same properties of a natural beachrock and can contribute positively to marine biodiversity as a natural rocky habitat.

An extensive oceanographic survey was conducted in the marine area between Kimolos and Sifnos Islands, a rather poorly-studied sector of the Aegean Sea, in order to gain better understanding of submarine geomorphological features and associated sediment provenance. Multi-beam bathymetry and surface sediment sampling with a box corer were carried out on board R/V Aegaeo, followed by grain-size analysis, XRD and XRF measurements. A large circular depression was identified north of Kimolos reaching a water depth of 743 m, filled with fine grained sediments. Surface sediment distribution is characterized by gradual decrease in grain-size from silty sand to silt in a S-N direction. The mineralogical composition comprises calcite, Mgcalcite, aragonite, dolomite, quartz, K feldspars, plagioclase, amphiboles and clay minerals. Major sediment provinces identified were: (i) the shallow sector proximal to Kimolos, characterized by higher contents in Si, Al, K, Rb and Ba; (ii) the deep area west of Sifnos, including the large depression, characterized by higher contents in Fe, Ti, Na, Mg, S, Cr, Cu, Ni, V, Zn; and (iii) the south passage between Kimolos and Sifnos, which exhibits higher Ca, S, and Sr contents. Manganese enrichment was observed in and around the bathymetric depression, where Mn oxides act efficiently as scavengers of a suite of metals.