The development of alternate clean energy resources is among the most pressing issues in the energy sector in order to preserve the global natural environment. One of the ideal candidates is the utilization of hydrogen as a primary fuel in lieu of fossil fuels. It can be safely stored in liquid organic hydrogen carrier (LOHC) materials and recovered on demand. A uniform supply of hydrogen is essential for power production systems for their smooth operation. This study was conducted to determine the operating conditions of the dehydrogenation of perhydro-dibenzyltoluene (H18-DBT) to ensure that hydrogen supply in a continuous flow reactor remains stable over a wide range of temperatures. The hydrogen flow rate from the dehydrogenation reaction was measured and correlated with the degree of dehydrogenation (DoD) evaluated from the refractive index of reactant liquid samples at various temperatures, WHSV and the initial reactant concentrations. Moreover, a kinetic model is presented holding validity up to a WHSV of 67 h⁻¹. The results acquired present a range for an order of reaction from 2.3 to 2.4 with the required activation energy of 171 kJ/mol.

Hybrid renewable energy systems with photovoltaic and energy storage systems have gained popularity due to their cost-effectiveness, reduced dependence on fossil fuels and lower CO₂ emissions. However, their techno-economic advantages are crucially dependent on the optimal sizing of the system. Most of the commercially available optimization programs adopt an algorithm that assumes repeated weather conditions, which is becoming more unrealistic considering the recent erratic behavior of weather patterns. To address this issue, a data-driven framework is proposed that combines machine learning and hybrid metaheuristics to predict weather patterns over the lifespan of a hybrid renewable energy system in optimizing its size. The framework uses machine learning tree ensemble methods such as the cat boost regressor, light gradient boosting machine and extreme gradient boosting to predict the hourly solar radiation and load demand. Nine different hybrid metaheuristics are used to optimize the hybrid renewable energy system using forecasted data over 15 years, and the optimal sizing results are compared with those obtained from 1-year data simulation. The proposed approach leads to a more realistic hybrid renewable energy system capacity that satisfies all system constraints while being more reliable and environmentally friendly. The proposed framework provides a robust approach to optimizing hybrid renewable energy system sizing and performance evaluation that accounts for changing weather conditions over the lifespan of the system.

Owing to the massive expansion and intermittent nature of renewable power, green hydrogen production, storage, and transportation technologies with improved economic returns need to be developed. Moreover, the slowness of the dehydrogenation reaction is a primary barrier to the commercialization of liquid organic hydrogen carrier (LOHC) technology. The present study focused on increasing the speed of dehydrogenation, resulting in the proposal of a triple-loop dehydrogenation system comprising reaction, heating, and chilling loops. The reactor has a rotating cage containing a packed bed of catalyst pellets, which is designed to enhance both heat and mass transfer by helping to detach precipitated hydrogen bubbles from the catalyst surface. In addition, the centrifugal force aids in isolating the gas phase from the LOHC liquid. A dehydrogenation experiment was conducted using the reaction and chilling loops, which revealed that the average hydrogen production rate during the first hour was 52.6 LPM (liter per minute) from 26.3 L of perhydro-dibenzyl-toluene with 1.5 kg of 0.5 wt% Pt/Al₂O₃ catalyst. This was approximately 48% more than the value predicted with the reaction kinetics measured with a small-scale plug flow dehydrogenation reactor with less than 1.0 g of 5.0 wt% Pt/Al₂O₃ catalyst. The concept, construction methods, and results of the preliminary gas infiltration, flow visualization, and reactor pumping experiments are also described in this paper.

To increase the efficiency of a fuel processor and HT-PEMFC (high temperature-proton exchange membrane fuel cell) combined system, it is essential to improve the efficiency of the fuel processor. In this research, the fuel processor was simulated by the Aspen Hysys^® simulator, and the effect of the various operating conditions on the total efficiency was investigated. The thermal efficiency of the fuel processor increased as the temperature and S/C (steam-to-carbon) ratio increased, and the efficiency was higher at an S/C ratio of 3 than at an S/C of 4 with a reformer temperature of 700 °C and higher. Under the selected operating conditions of the fuel processor, the recycling of unreacted hydrogen from the anode off-gas (AOG) of the HT-PEMFC improved the overall efficiency of the combined fuel processor and HT-PEMFC by a factor of 1.28. The operating conditions where the AOG supplied more heat than was required for fuel processor operation were excluded. The high-efficiency operating conditions of the fuel cell system were proposed with the target of 5 kW of output as the capacity of the household HT-PEMFC.

To increase the efficiency of fuel processor and HT-PEMFC (High Temperature-Proton Exchange Membrane Fuel Cell) combined system, it is essential to improve the efficiency of a fuel processor. In this research, the fuel processor was simulated by Aspen Hysys® simulator, and effect of the various operating conditions on the total efficiency was investigated. Thermal efficiency of the fuel processor increased as the temperature and S/C (Steam to carbon) ratio increased, and the efficiency was higher at the S/C ratio of 3 than at the S/C of 4 at the reformer temperature of 700 ℃ and higher. Under the selected operating conditions of the fuel processor, recycling of unreacted hydrogen from the anode off gas (AOG) of the HT-PEMFC improve the overall efficiency of the combined fuel processer and HT-PEMFC by a factor of 1.28. Operating conditions where the AOG supplied excessive heat than required for fuel processor operation were excluded. The high-efficiency operating conditions of the fuel cell system were proposed with the target of 5 kW of output as the capacity of the household HT-PEMFC.