Solid-liquid phase transitions in single crystal Cu during shock and subsequent release are studied with large-scale classical molecular dynamics simulations. During shock compression, although the equilibrium states far behind shock front converge to the same Hugoniot, the pathways from metastable states right behind the shock front to the final equilibrium states and the resulting microstructures are orientation-dependent. Premelting is followed by recrystallization of supercooled melt into a polycrystalline solid for the [110] and [111] shocks, and a superheated, more ordered, solid is observed prior to shock melting for the [100] shock. The differences in the microstructure in the behind-shock region in turn give rise to different release melting behaviors (including premelting and superheating) along different release paths for these loading orientations.
This work investigates the shock-induced microjetting from a grooved surface (10 nm, 120 degree) of low-melting metal Pb with molecular dynamics simulations. The microjetting processes under surface/release melting conditions are presented in detail, and some properties on the microjet mass and velocity are revealed for different shock pressure and profile cases. It is found that the increase of microjet mass with shock pressure experiences three stages: rapid increase (solid phase), slowdown increase (release melting) and almost no increase (shock melting). For all cases, the ratio of the maximal jetting velocity to the surface velocity approximately keeps a constant (1.5–1.55), but this value undergoes a degree of exponential decay with time for the solid release cases. In addition, the temperature of the microjet is found to be always above the melting point (zero pressure) and keep a continuous increase towards the microjet tip. When introducing slow decaying profiles, the microjet mass begins to increase with the decay rate, which is dominated by the deformation of bubble during pull-back. When the decay rate becomes fast enough, the microspall occurs as expected, meanwhile the microjet appears to reduce because of the shock energy reduction. But that cannot cut off the microjet completely. The velocity distribution along the loading direction shows two linear regions corresponding to the microspall and microjet, and the latter seems to have a greater velocity gradient.
We perform large-scale molecular dynamics simulations to study shock-induced melting transition of idealized hexagonal columnar nanocrystalline Cu. The as-constructed nanocrystalline Cu consists of unrotated (reference) and rotated columnar crystals, relative to the columnar axis. Shock loading is applied along three principal directions of the columnar Cu: two transverse (zigzag and armchair) and one longitudinal directions. Dynamic local melting processes are highly anisotropic with respect to the shock directions. For the transverse directions, hotspot effect and disparate dynamic responses of grains with different orientations may lead to partial or complete premelting of the initially rotated grains, which in turn leads to transient supercooling and heterogeneous recrystallization, and thus, the formation of nanocrystalline solids with modified grain structures or solid-liquid mixtures, depending on the extent of supercooling. With increasing shock strengths, the reference grains melt heterogeneously at interfaces and homogeneously inside. Conversely, “bulk” premelting of the rotated grains is absent for the longitudinal direction, except for grain boundary melting. The progression of recrystallization or heterogenous melting diminishes and eventually eliminates the transient premelting or superheating of the system via latent heat and thermal diffusion. Premelting or superheating appears unlikely for bulk melting or well-defined Hugoniot states, if the thermal and mechanical equilibria are achieved, and the thermodynamic melting curve coincides with the partial melting Hugoniot states of a polycrystalline solid.
25 May 2018 in Journal of Physics: Condensed Matter
With classic molecular dynamics simulations, we investigate the effects of temperature and void on the bcc to hcp/fcc structural transition in single crystal iron driven by 1D ([0 0 1]) and 3D (uniform) compressions. The results show that the pressure threshold does not reduce monotonously with temperature. The pressure threshold firstly increases and then decreases in the range of 60–360 K under 1D compression, while the variation trend is just opposite under 3D compression. As expected, the initial defect may lower the pressure threshold via heterogenous nucleation. This effect is found to be more distinct at lower temperature, and the heterogenous nucleation mainly results in hcp structure. Under the condition of strain constraint, the products of structural transition will respectively form flaky hcp twin structure ((1 0 0) or (0 1 0)) and lamellar structure ({1 1 0}) of mixed phases under 1D and 3D compressions. During the structural transition, we find the shear stress (1D compression) of hcp phase is always lower than that of bcc phase. The cold energy calculations indicate that the hcp phase is the most stable under high pressure. However, we observe the evident metastable state of bcc phase, whose energy will be much higher than both hcp and fcc phases, and then provides the possibility for the occurrence of fcc nucleation.