The transverse vibration characteristics and stability of a moving membrane with several intermediate elastic supports are investigated considering the translating speed. The motion equations of the vibration system are derived according to the membrane vibration theory and the D'Alembert principle. The constraint of the middle printing roller to the membrane is used as the intermediate support which is replaced by the constraint force. And the vibration characteristic equation is established by using Laplace transformation method and the numerical calculation method. Finally, the relationships between the natural frequency of the moving membrane and the translating speed, tension, supporting position and rigidity modulus are analyzed respectively, and the critical speed when the membrane is in a stable state is obtained. The conclusions provide a theoretical basis and effective approaches for improving the work stability of the printing press.
1 December 2013 in Journal of Low Frequency Noise, Vibration and Active Control
Nowadays more and more materials can be manufactured or stored in continuous web form. The vibration of the moving web limits the productivity and quality of the web materials. The active vibration control of the moving web with varying density is considered in this paper. Finite difference method is used to discretize the dynamic equations of the moving web with varying density and derive the state equation of transverse vibration control system for the moving web with varying density. The simulation of the response and decay process of transverse vibration for the moving web with varying density after the implementation of suboptimal control is performed by numerical calculation.
As a major branch of Non-Photorealistic Rendering (NPR), image stylization mainly uses computer algorithms to render a photo into an artistic painting. Recent work has shown that the ex-traction of style information such as stroke texture and color of the target style image is the key to image stylization. Given its stroke texture and color characteristics, a new stroke rendering method is proposed. By fully considering the tonal characteristics and the representative color of the original oil painting, it can fit the tone of the original oil painting image into a stylized image whilst keeping the artist’s creative effect. The experiments have validated the efficacy of the proposed model in comparison to three state-of-the-arts. This method would be more suitable for the works of pointillism painters with a relatively uniform style, especially for natural scenes, otherwise, the results can be less satisfactory.
Slot-die coating is widely used in the preparation of negative electrodes for lithium batteries. The thickness of the negative electrode has a significant influence on the battery performance and lifespan, and different manufacturers have different requirements for its thickness. In order to reduce the waste caused by trial and error in the electrode preparation process, a prediction model for the negative electrode thickness was established and verified through simulation and experiments. Based on the Landau–Levich film equation and the Ruschak model, a high-precision prediction model was constructed by taking into account the influence of factors’, such as temperature and slurry, spreading characteristics on the coating thickness. The minimum coating thickness and its influencing factors were explored. Meanwhile, the simulation analysis of the coating thickness was performed, and the theoretical values of three common process parameters were compared with the simulation results, showing a deviation of only 2.9%. An experiment on predicting the thickness of the negative electrode of lithium batteries was conducted. Thickness measurements were performed on the samples prepared through the experiment and compared with theoretical values. The accuracy rate of this thickness prediction model can reach 98.75%.
The effects of substrate roughness and impact angle on the spreading behavior of Polyvinylidene Fluoride (PVDF) slurry droplets during the spraying process using a dispersing disk are investigated, aiming to enhance the quality of lithium-ion battery separators. In this study, through theoretical modeling and simulation analysis, mathematical expressions for the maximum spreading coefficient and the final shrinking coefficient of the droplets are derived. A simulation model for droplet impact and diffusion on the substrate surface is established based on the Lattice Boltzmann Method (LBM) and the Lagrangian function. Simulation results indicate that the maximum spreading coefficient of the droplet decreases with increasing substrate roughness and impact angle, while the final shrinking coefficient increases with substrate roughness but decreases as the impact angle increases. Finally, spray coating experiments for lithium-ion battery separators are conducted, and the results show that as the surface roughness and impact angle of the substrate increase, the average diameter of the droplets decreases, thereby validating the accuracy of the simulation results.
The web-wrinkle phenomenon always occurs in the roll-to-roll coating production process, which leads to the decline of coating quality and an increase in waste. A theoretical analysis of the phenomenon is presented, and a simulation research method is proposed for the study. The method is outlined as follows: Initially, the web’s surface on the guide roll is modeled as a thin shell, with the relationship between web displacement and strain established through the nonlinear large deflection theory. The differential equations of the web are derived based on the internal-force equilibrium relationship. Subsequently, the boundary conditions are established according to the transfer of the web on the guide roller’s surface, and the deflected surface functions satisfying these conditions are obtained. The static method was used to determine the critical load for a web wrinkle, considering the friction between the web and the guide roll. Finally, finite element simulation analysis was conducted to ascertain the factors affecting the critical wrinkling load of the web. Through the analysis, the accuracy of the formulas used to calculate the critical compression load of the web was determined. The critical wrinkling load increases with the web thickness, web tension, and modulus of elasticity. The critical compressive stress of a web wrinkle was found to be proportional to the web thickness, modulus of elasticity, tension, and coefficient of friction. The rational selection of these parameters provides a theoretical foundation for improving the quality of coating production.