Chen Guo

Chen Guo


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 October 2021 in Remote Sensing
Verified
Journal Article
Open access
PDF file
QXQiang Xu
Qiang Xu
CGChen Guo
Chen Guo
XDXiujun Dong
Xiujun Dong
WLWeile Li
Weile Li
HLHuiyan Lu
Huiyan Lu
XLXiaosha Liu
Xiaosha Liu
Interferometric synthetic aperture radar (InSAR) technology is known as one of the most effective methods for active landslide identification and deformation monitoring in large areas, and thus it is conducive to preventing and mitigating the losses caused by landslides. However, great uncertainty inevitably exists due to influences of complex terrains, dense vegetations, and atmospheric interferences in the southwestern mountainous area of China, and this is associated with false or erroneous judgment during the process of landslide identification. In this study, a landslide identification method is put forward by integrating InSAR technology and airborne light detection and ranging (LiDAR) technology. Via this method, surface deformation characteristics detected by InSAR technology and micro-geomorphic features reflected by LiDAR technology were used to identify and map landslides of large areas. Herein, the method was applied to process 224 Sentinel-1 images covering Danba County and its surrounding areas (540 km2) from October 2014 to September 2020. Firstly, 44 active landslides with total areas of 59 km2 were detected by stacking InSAR technology. Then, major regions up to 135 km2 were validated by data gained from the airborne LiDAR technology. Particularly, several large landslides with lengths and/or widths of more than 2 km were found. Further, the precipitation data were integrated with the above results to analyze the temporal deformation characteristics of three typical landslides from major regions via SBAS InSAR technology. The key findings were as follows: (1) The combination of InSAR and LiDAR technologies could improve the accuracy of landslide detection and identification; (2) there was a significant correlation between temporal deformation characteristics of some landslides and monthly rainfall, with an obvious hysteretic effect existing between the initiation timing of rainfall and that of deformation; (3) the results of this study will be important guidance for the prevention and control of geological hazards in Danba County and areas with similar complex geomorphological conditions by helping effectively identify and map landslides.

24 June 2022 in Remote Sensing
Verified
Journal Article
Open access
PDF file
QXQiang Xu
Qiang Xu
ZYZhen Ye
Zhen Ye
QLQian Liu
Qian Liu
XDXiujun Dong
Xiujun Dong
WLWeile Li
Weile Li
CGChen Guo
Chen Guo
Airborne light detection and ranging (LiDAR) and unmanned aerial vehicle-structure from motion (UAV-SfM) provide point clouds with unprecedented resolution and accuracy that are well suited for the digital characterization of rock outcrops where direct contact measurements cannot be obtained due to terrain or safety constraints. Today, however, how to better apply these techniques to the practice of geostructural analysis is a topic of research that must be further explored. This study presents a processing procedure for extracting three-dimensional (3D) rock structure parameters directly from point clouds using open-source software and a three-dimensional distinct element code-assisted (3DEC) simulation of slope failure based on carbonate rock cliffs in the Jiuzhaigou Scenic Area. The procedure involves (1) processing point clouds obtained with different remote sensing techniques; (2) using the Hough transform to estimate normals for the hue, saturation, and value (HSV) rendering of unstructured point clouds; (3) automatically clustering and extracting the set-based point clouds; (4) estimating set-based geometric parameters; and (5) performing a subsequent stability analysis based on rock structure parameters. The results show that integrating different remote sensing techniques and rock structure computing can provide a quick way for slope engineers to assess the safety of blocky rock masses.