Behrouz Bagheri

Dr. Behrouz Bagheri


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 January 2021 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
AAAmin Abdollahzadeh
Amin Abdollahzadeh
BBBehrouz Bagheri
Behrouz Bagheri
MAMahmoud Abassi
Mahmoud Abassi
AKAmir Hossein Kokabi
Amir Hossein Kokabi
AMAhmad Ostovari Moghaddam
Ahmad Ostovari Moghaddam

8 May 2024 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
BBBehrouz Bagheri
Behrouz Bagheri
AAAmin Abdollahzadeh
Amin Abdollahzadeh

12 October 2022 in Metals and Materials International
Verified
Journal Article
Closed access
PDF file
BBBehrouz Bagheri
Behrouz Bagheri
ASAli Shamsipur
Ali Shamsipur
AAAmin Abdollahzadeh
Amin Abdollahzadeh
SMSeyyed Ehsan Mirsalehi
Seyyed Ehsan Mirsalehi

7 July 2021 in International Journal of Material Forming
Verified
Journal Article
Closed access
PDF file
MAMahmoud Abbasi
Mahmoud Abbasi
BBBehrouz Bagheri
Behrouz Bagheri
AAAmin Abdollahzadeh
Amin Abdollahzadeh
AMAhmad Ostovari Moghaddam
Ahmad Ostovari Moghaddam

5 September 2022 in Welding in the World
Verified
Journal Article
Closed access
PDF file
AVAlireza Heidari Vaneghi
Alireza Heidari Vaneghi
BBBehrouz Bagheri
Behrouz Bagheri
ASAli Shamsipur
Ali Shamsipur
SMSeyyed Ehsan Mirsalehi
Seyyed Ehsan Mirsalehi
AAAmin Abdollahzadeh
Amin Abdollahzadeh

6 August 2024 in Journal of Composite Materials
Verified
Journal Article
Closed access
AAAmin Abdollahzadeh
Amin Abdollahzadeh
BBBehrouz Bagheri
Behrouz Bagheri
AMAbbas Masoudi Morghmaleki
Abbas Masoudi Morghmaleki
AMAhmad Ostovari Moghaddam
Ahmad Ostovari Moghaddam
AEAli Reza Eivani
Ali Reza Eivani
In this article, dissimilar magnesium and aluminum alloys were welded with a Zn interlayer and TiC nanoparticles by friction stir welding. Optimal joining conditions were achieved by a combination of three traverse speeds (30, 45, and 60 mm/min) and constant rotational speeds (1050 rpm). The best microstructure evolution and mechanical properties were achieved for specimens joined at rotational and traverse speeds of 1050 rpm and 45 mm/min, respectively. The grain size decreases as the traverse speed increases from 30 to 45 mm/min due to a reduction in heat input, an improvement in reinforcing distribution, and high intermixing of materials, then increases from 45 to 60 mm/min due to inadequate heat input for recrystallization process. It was shown that the TiC particles play a prominent role in the microstructure modification and enhance mechanical properties of weld samples while the Zn foil interlayer plays a vital in avoiding the formation of Al-Mg IMC phases. The obtained result under optimal welding parameters indicates that MgZn2, Mg-Al-Zn compounds, Mg and Al solid solution, were the main detected common phases in the stir zone instead of the brittle and hard Al-Mg IMCs formation. The average hardness values of 232 Hv were achieved, while the strength of the weld specimen experiences the 189 MPa value. In addition, a combination of brittle and ductile modes was observed based on the fracture surface of the weld sample after the tensile test.