Polypropylene (PP) and Polyethylene (PE) are widely used commodity plastics in packaging industry such as detergent bottles. To produce plastic detergent bottles, very often extrusion blown molded PE-HD as a body and injection molded PP as a screw cap are used. Separation of individual polymer type is difficult due to the similar density. Unfortunately, the melt blending of recycled post-consumer detergent bottle waste leads to deterioration of mechanical properties. Additionally, the percentage of rPP contamination in recycled PE-HD (rPE-HD) from post-consumer bottle waste can be varied depending on local waste composition and different sorting quality. This work investigates the effect of various contamination scenarios with different percentage of rPP from bottle caps in rPE-HD from bottle waste as well as their compatibilization with olefin block copolymer (OBC) on mechanical, thermal, and rheological properties. Moreover, the low temperature tensile properties of blends with OBC are also investigated in this study. The results showed that the increasing rPP contamination leads to deteriorating elongation at break and tensile impact strength. Furthermore, the addition of OBC as a compatibilizer into worse-case contamination scenario (15 wt% rPP in rPE-HD) significantly improved elongation at break and tensile impact strength. Scanning electron microscopy (SEM) confirms the improvement in adhesion between rPP and rPE-HD from recycled bottle waste with the addition of OBC as a compatibilizer. Rheological measurements reveal the interfacial interaction among rPP, rPE-HD and OBC. The low temperature tensile test demonstrated that the addition of OBC as a compatibilizer improved low temperature tensile elongation at break.

Plastic recycling strikes a balance between functional, mass producible products and environmental sustainability and is pegged by governments for rapid expansion. However, ambitious targets on recycled material adoption across new markets are at odds with the often heterogenous properties of contaminated regranulates. This study investigated polypropylene (PP) contamination in post-consumer low-density polyethylene (PE-LD) and mixed polyolefin (PO) regranulates. Calibration curves were constructed and PP content, its effect on mechanical properties and property recovery in compatibilised material assessed. FT-IR band ratios provided more reliable estimations of PP content than DSC melt enthalpy, which suffered considerable error for PP copolymers. PE-LD regranulates contained up to 7 wt.% PP contamination and were considerably more brittle than virgin PE-LD. Most mixed PO regranulates contained 45–95 wt.% PP and grew more brittle with increasing PP content. Compatibilisation with 5 wt.% ethylene-based olefin block copolymer resulted in PE-LD blends resembling virgin PE-LD and considerable improvements in the properties of mixed PO blends. These results illustrate the prevalence of PP in recycled PE, challenges associated with its quantification, effect on mechanical properties, and compatibilisation viability, thereby representing an important step towards higher quality regranulates to meet the recycling demands of tomorrow.

The most widely used commodity polymers in the rigid packaging industry are polypropylene (PP) and high-density polyethylene (HDPE). For example, blow molding grade of HDPE as a bottle and injection molding grade of PP as a cap are often used to produce detergent bottles. Therefore, the recycled HDPE bottles from post-consumer waste include PP as a contaminant originated from PP bottle caps. To simulate mechanical recycling of bottle waste, the mechanical properties of HDPE-rich-HDPE/PP virgin model blend were studied. For compatibilization, ethylene-based olefin block copolymer, propylene-based olefin block copolymer, ethylene propylene random copolymer, and styrene-butadiene-styrene triblock copolymer were chosen as potential compatibilizer candidates. Contact angle measurements, morphological analysis, adhesion tests of compatibilizer candidates to polymer blend components and the tensile as well as tensile impact properties of the ternary blends were studied. It was found that the ethylene-based olefin block copolymer was the most effective compatibilizer resulting in a return of mechanical properties to those of neat vHDPE due to its ability to encapsulate dispersed vPP particles in a vHDPE matrix (core-shell morphology) and the best adhesion to polymer blend components.