Kanji Ono

Prof. Kanji Ono

University of California, Los Angeles, CA 90095, USA
+1
orcid

Research Focus & Metrics

Academic Career Length

36Years (1991-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 March 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Kanji OnoKanji Ono
Kanji Ono
In this paper, ultrasonic attenuation of engineering materials is evaluated comprehensively, covering metals, ceramics, polymers, fiber-reinforced composites, wood, and rocks. After verifying two reliable experimental methods, 336 measurements are conducted and their results are tabulated. Attenuation behavior is determined over broadband spectra, extending up to 15 MHz in low attenuating materials. The attenuation spectra are characterized in combination with four power law terms, with many showing linear frequency dependence, with or without Rayleigh scattering. Dislocation damping effects are re-evaluated and a new mechanism is proposed to explain some of the linear frequency dependencies. Additionally, quadratic and cubic dependencies due to Datta–Kinra scattering and Biwa scattering, respectively, are used for some materials to construct model relations. From many test results, some previously hidden behaviors emerged upon data evaluation. Effects of cold working, tempering, and annealing are complex and sometimes contradictory. Comparison to available literature was attempted for some, but most often prior data were unavailable. This collection of new attenuation data will be of value in materials selection and in designing structural health monitoring and non-destructive inspection protocols.

11 June 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Kanji OnoKanji Ono
Kanji Ono
This review introduces several areas of importance in acoustic emission (AE) technology, starting from signal attenuation. Signal loss is a critical issue in any large-scale AE monitoring, but few systematic studies have appeared. Information on damping and attenuation has been gathered from metal, polymer, and composite fields to provide a useful method for AE monitoring. This is followed by discussion on source location, bridge monitoring, sensing and signal processing, and pressure vessels and tanks, then special applications are briefly covered. Here, useful information and valuable sources are identified with short comments indicating their significance. It is hoped that readers note developments in areas outside of their own specialty for possible cross-fertilization.

24 June 2016 in Materials
Verified
Journal Article
Open access
PDF file
Kanji OnoKanji Ono
Kanji Ono
This study examined outstanding issues of sensitivity calibration methods for ultrasonic and acoustic emission transducers and provides workable solutions based on physically measureable quantities, laser-based displacement measurement in particular. This leads to mutually consistent determination of transmitting and receiving sensitivities of sensors and transducers. Methods of circumventing problems of extraneous vibrations on free transmitters are used, giving the foundation for face-to-face calibration methods. Working on many ultrasonic and acoustic emission transducers, their receiving and transmitting sensitivities are found to be always different, while their ratios exhibit unexpected similarity. This behavior is attributed to monopolar pulse generation and bipolar received signals due to electrical charge transfer during elastic wave motion and reflection on the back face. This is verified through a quantitative piezoelectric sensing experiment. Displacement vs. velocity calibration terminology is clarified, redefining the “V/µbar” reference for contact sensor calibration. With demonstrated differences in the transmitting and receiving sensitivities of transducers, the requirement of the Hill-Adams equation invalidates the basic premise of the currently formulated reciprocity calibration methods for acoustic emission transducers. In addition, the measured reciprocity parameter for the case of through-transmission significantly deviates from the approximate theoretical prediction. It is demonstrated that three methods provide reliable sensor calibration results that are complimentary among them.

16 April 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Kanji OnoKanji Ono
Kanji Ono
This study examines methods for simplifying estimation of the Weibull modulus. This parameter is an important instrument in understanding the statistical behavior of the strength of materials, especially those of brittle solids. It is shown that a modification of Robinson’s approximate expression can provide good estimates of Weibull modulus values (m) in terms of average strength (<σ>) and standard deviation (S): m = 1.10 <σ>/S. This modified Robinson relation is verified on the basis of 267 Weibull analyses accompanied by <σ> and S measurements. Estimated m values matched normally obtained m values on average within 1%, and each pair of m values was within ± 20%, except for 11 cases. Applications are discussed, indicating that the above relation can offer a quantitative tool based on the Weibull theory to engineering practice. This survey suggests a rule of thumb: ductile metal alloys have Weibull moduli of 10 to 200.

30 July 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Kanji OnoKanji Ono
Kanji Ono
In this paper, ultrasonic attenuation of the transverse waves of engineering materials is evaluated, covering metals, ceramics, polymers, fiber-reinforced plastics, and rocks. After verifying experimental methods, 273 measurements are conducted and their results are tabulated. Fifty of the tests are for the longitudinal mode. Attenuation behavior is determined over broadband spectra. The attenuation spectra are characterized in four patterns, with 2/3 of the tests showing linear frequency dependence and another ¼ linear spectrum plus Rayleigh scattering (Mason-McSkimin relation). The longitudinal and transverse damping factors varied from 0.004 to 0.065, which are 1/3 to 5 times those of polymethyl methacrylate, suggesting that almost all the engineering materials tested may be viscoelastic. The present test results make the term dynamic viscosity more appropriate for exploring the underlying processes. The observed results were compared between the longitudinal and transverse modes and among similar material types. In more than a half of the tests, the transverse attenuation coefficients were higher than the corresponding longitudinal attenuation coefficients by 1.5× or more. Some material groups had similar attenuation coefficients for the two modes. Since the physical basis for viscous damping is hardly understood, especially in hard solids, further studies from new angles are keenly desired. This collection of new attenuation data will be of value for such works. Practically, this will assist in materials selection and in designing structural health monitoring and non-destructive inspection protocols.

29 October 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Kanji OnoKanji Ono
Kanji Ono
Acoustic emission (AE) techniques have successfully been used for assuring the structural integrity of large rocket motorcases since 1963