Cable-driven parallel mechanism is a special kind of parallel robot in which traditional rigid links are replaced by actuated cables. This provides a new suspension method for wind tunnel test, in which an aircraft model is driven by a number of parallel cables to fulfil 6-DOF motion. The workspace of such a cable robot is limited due to the geometrical and unilateral force constraints, the investigation of which is important for applications requiring large flight space. This paper focuses on the workspace analysis and verification of a redundant constraint 6-DOF cable-driven parallel suspension system. Based on the system motion and dynamic equations, the geometrical interference (either intersection between two cables or between a cable and the aircraft) and cable tension restraint conditions are constructed and analyzed. The hyperplane vector projection strategy is used to solve the aircraft’s orientation and position workspace. Moreover, software ADAMS is used to check the workspace, and experiments are done on the prototype, which adopts a camera to monitor the actual motion space. In addition, the system construction is designed by using a built-in six-component balance to measure the aerodynamic force. The results of simulation and tests show a good consistency, which means that the restraint conditions and workspace solution strategy are valid and can be used to provide guidance for the cable-driven parallel suspension system’s application in wind tunnel tests.
8 August 2016 in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
Cable-driven parallel robot is a special kind of robot, which is actuated by cables. It is already applied in the low speed wind tunnel to get aerodynamic measurement of aircraft model, and the aircraft pose could be adjusted by changing the cable length. Whether it can be used in hypersonic wind tunnel still needs further discussion. This paper presents the dynamics and aerodynamics analysis of a large-scale model supported by 6-DOF cable-driven parallel robot to investigate the feasibility of this special kind of suspension system in hypersonic wind tunnel. The description of this setup with a X-51A-like model is given, and then based on the system dynamic equations, aerodynamic force and stiffness matrix are derived. In the simulation, properties of dynamics and aerodynamics are mainly concerned. A typical shock tunnel with flow duration of about 100 milliseconds is taken as an example, and results show that the system is stable enough to meet the fundamental static wind tunnel test. From the cable tension variation under impact load and the sensitivity analysis, it is likely accessible to derive the aerodynamic forces. Compared with the sting suspension method, cable-driven parallel robot has the priority of higher inherent frequency and more flexible degrees. The interference to the flow field induced by cables is also preliminarily proved to be small by the CFD simulation, which can be acceptable and corrected. Researches conducted show the feasibility of cable-driven parallel robot’s application in hypersonic wind tunnel.
Unsteady aerodynamic prediction at high angles of attack is of great importance to the design and development of advanced fighters. In this paper, a weighted feature fusion model (WFFM) that combines the state-space model and neural networks is proposed to build an unsteady aerodynamic model for the precise simulation and control of post-stall maneuvers. In the proposed model, the influences of the physical model on neural networks are considered and adjusted by introducing a standardization layer and a new weighting method. A long short-term memory (LSTM) network is used to fuse two mappings: one from flight states to aerodynamic loads, and the other from low-fidelity data to high-fidelity data. Data from wind tunnel oscillation experiments at high angles of attack using a new kind of wire-driven parallel robot and the traditional tail support are used for verifying the proposed aerodynamic model. The output of the WFFM is also compared with predictions from other models, such as the state-space model, single LSTM model, and feature fusion model not including a feature weighting layer. Results demonstrate improved accuracy of the proposed model in the interpolation and extrapolation tests. Furthermore, the WFFM is applied to the flight simulation of F-16 with different control inputs. Compared with conventional models, the WFFM shows improved accuracy and better generalization capability.
This paper investigates an intelligent method for the motion control of a cable-driven parallel suspension system (CDPSS) in wind tunnel tests, especially at high angles of attack, which is characterized by unsteady and nonlinear aerodynamics. Considering the modeling uncertainties and the complex aerodynamic interference, a composite controller that combines deep deterministic policy gradient (DDPG) and computed-torque is proposed to improve the control performance. The tasks at hand consist in the construction of the training environment based on the dynamic equations and the Markov Decision Process (MDP) design. The supplementary computed-torque control is used to enhance the learning rate of the agent. Then a well-trained agent is applied in the high angles of attack maneuvers control with different examples, including single-DOF and multi-DOF coupled motion. The simulation results show the controller could fulfill the training tasks efficiently, and it turns out to be robust and maintain strong generalization ability despite handling the unlearned tasks.
The high-speed oblique water entry of a segmented vehicle presents a complex multiphase fluid–structure interaction (FSI) problem, characterized by the evolution of the vapor–liquid cavity and the transient impact loads transmission. This study constructs a high-fidelity numerical model that integrates a multiphase flow solver with a FSI solver to investigate the underlying fluid physics and shock response during initial water entry for a segmented vehicle connected by bolts. The effects of key parameters such as entry velocity and angle on the spatiotemporal evolution of cavity, impact loads transmission, and shock response spectrum (SRS) are systematically investigated. Results show that multiphase FSI during cavity evolution notably amplifies high-frequency fluctuations in acceleration and induces asymmetry stress wave propagation. Segments with longer propagation distances exhibit higher peak axial forces, while connection interfaces experience negative normal contact forces and lateral contact moments. SRS analysis reveals resonant amplification peaks at 600 and 1500 Hz across the segments, with amplitudes reaching 100 g, and higher peaks at the monitoring points. Stress concentration and wave asymmetry generate elevated local stresses at connections and bolts, necessitating protective measures targeting segment-specific load peaks, critical frequency bands, and interface/bolt reinforcement. This study provides an effective multiphase FSI simulation framework and insights into the flow and shock characteristics of a segmented vehicle during high-speed water entry.