The paper discusses the possibility of obtaining a uniformly inhomogeneous surface of aluminum alloy 6063 as a result of alkaline etching and laser processing. Further surface treatment with ethanol solutions of octadecylphosphonic (ODPA) and stearic acids leads to its superhydrophobization (SHP). The study of the degradation kinetics of SHP coatings in water and under conditions of neutral salt spray showed the high stability of ODPA films obtained on a laser-textured surface with an irregularities height of 9.82 μm. X-ray photoelectron spectroscopy (XPS) results showed that ODPA is chemisorbed on the alloy surface. High corrosion resistance of the surface with superhydrophobic layers confirmed by polarization measurements, electrochemical impedance spectroscopy (EIS) and corrosion tests.

Using a combination of chemical coprecipitation and hydrothermal treatment of the resulting dispersed system, a hierarchically organized NiCo₂O₄ nanopowder was obtained, consisting of slightly elongated initial oxide nanoparticles self-organized into nanosheets about 10 nm thick, which in turn are combined into hierarchical cellular agglomerates of about 2 μm. Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction analysis (XRD), selected area electron diffraction (SAED) and high-resolution transmission electron microscopy (HR-TEM) allowed to confirm the formation of NiCo₂O₄ powder with the desired crystal structure via additional heat treatment of the intermediate product. Energy-dispersive X-ray spectroscopy (EDX) was used to confirm the target metal ratio, and the uniform distribution of the elements (Ni, Co and O) was shown by mapping. The resulting nanopowder was employed to prepare functional inks suitable for microplotter printing of the NiCo₂O₄ film. It was found that an oxide film morphology is fully inherited from the hierarchically organized oxide nanopowder used. Atomic force microscopy (AFM) revealed the film thickness (15 μm) and determined the maximum height difference of 500 nm over an area of 25 μm². Kelvin probe force microscopy (KPFM) showed that the surface potential was shifted to the depths of the oxide film, and the work function value of the material surface was 4.54 eV, which is significantly lower compared to those reported in the literature. The electronic state of the elements in the NiCo₂O₄ film under study was analyzed by X-ray photoelectron spectroscopy (XPS). Chemosensor measurements showed that the printed receptor layer exhibited selectivity and high signal reproducibility for ethanol detection. As the relative humidity increases from 0 to 75%, the response value is reduced; however, the sensor response profile and signal-to-noise ratio remain without significant changes.

Bimetallic catalysts containing platinum and transition metals (PtM, M = Mo, Ni, CoCr) were synthesized on carbon nanotubes (CNTs) functionalized in an alkaline medium. Their platinum content is 10–15% by mass. PtM/CNT_NaOH are active in both the hydrogen oxidation reaction (HOR) and the oxygen reduction reaction (ORR) in alkaline electrolytes. Although catalysts based on a single transition metal are inactive in the HOR, their activity in the cathode process of ORR increases relative to CNT_NaOH. When using the rotating ring-disk electrode method for ORR, PtM/CNT showed a high selectivity in reducing oxygen directly to water. In HOR, the PtM/CNT catalyst had an activity comparable to that of a commercial monoplatinum catalyst. The results obtained show that it is possible to use the PtM/CNT catalyst in an alkaline fuel cell both as an anode and as a cathode.

It has been shown that solutions of stearic acid in a dimethyl sulfoxide–water binary mixture allow superhydrophobic protective coatings to be created on an aluminum alloy surface with a minimum impact on the environment. The superhydrophobicity and self-cleaning ability of the coating that we developed have been confirmed by measurements of droplet wetting angles and roll-off angles. These properties appear due to the formation of a multimodal micro-rough surface that mainly consists of aluminum stearate. The coatings formed in this manner have been studied by ellipsometry, XPS, and scanning probe microscopy. Their protective ability has been estimated by the “droplet-express” method and in a salt fog chamber. The protective ability of the coating is determined by the DMSO/H₂O ratio, the concentration of stearic acid, and the duration and temperature of modification of the aluminum alloy; it is controlled by a competition between the processes of aluminum stearate formation and hydrolysis. It has been shown that adsorption of stearic acid on an aluminum stearate coating increases its permeability and decreases its protective capability. The results presented in this article are useful for optimizing the conditions of applying green superhydrophobic stearate coatings on aluminum alloys in order to achieve a maximum protective effect.