Liliana Cangueiro

Dr. Liliana Cangueiro


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2012 in Journal of Biomedical Optics
Verified
Journal Article
Closed access
PDF file
LCLiliana Cangueiro
Liliana Cangueiro
RVRui Vilar
Rui Vilar
Ana Maria P. L. R. Botelho Do RegoAna Maria P. L. R. Botelho Do Rego
Ana Maria P. L. R. Botelho Do Rego
VMVania S. F. Muralha
Vania S. F. Muralha
We study the surface topographical, structural, and compositional modifications induced in bovine cortical bone by femtosecond laser ablation. The tests are performed in air, with a Yb:KYW chirped-pulse-regenerative amplification laser system (500 fs, 1030 nm) at fluences ranging from 0.55 to 2.24  J/cm2. The ablation process is monitored by acoustic emission measurements. The topography of the laser-treated surfaces is studied by scanning electron microscopy, and their constitution is characterized by glancing incidence x-ray diffraction, x-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and micro-Raman spectroscopy. The results show that femtosecond laser ablation allows removing bone without melting, carbonization, or cracking. The structure and composition of the remaining tissue are essentially preserved, the only constitutional changes observed being a reduction of the organic material content and a partial recrystallization of hydroxyapatite in the most superficial region of samples. The results suggest that, within this fluence range, ablation occurs by a combination of thermal and electrostatic mechanisms, with the first type of mechanism predominating at lower fluences. The associated thermal effects explain the constitutional changes observed. We show that femtosecond lasers are a promising tool for delicate orthopaedic surgeries, where small amounts of bone must be cut with negligible damage, thus minimizing surgical trauma.

1 August 2016 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
ACA. Capelo
A. Capelo
MEM.A. Esteves
M.A. Esteves
ASA.I. de Sá
A.I. de Sá
RSR.A. Silva
R.A. Silva
LCLiliana Cangueiro
Liliana Cangueiro
Carmen M. RangelCarmen M. Rangel
Carmen M. Rangel

17 August 2016 in Journal of Physics D: Applied Physics
Verified
Journal Article
Closed access
PDF file
LCLiliana Cangueiro
Liliana Cangueiro
ACAndré Cavaleiro
André Cavaleiro
JMJerzy Morgiel
Jerzy Morgiel
RVRui Vilar
Rui Vilar
The present paper aims at investigating the mechanisms of imprinting LIPSS (laser-induced periodic surface structures), arrangements of parallel ripples with a periodicity slightly smaller than the radiation wavelength, on metallic surfaces. To this end, Ni/Ti multi-layered samples produced by magnetron sputtering were textured with LIPSS using a 1030 nm, 560 fs pulse duration laser and pulse frequency of 1 kHz, and the resulting surfaces were investigated by scanning and transmission electron microscopies. The results obtained show that the core of the ripples remains in the solid state during the laser treatment, except for a layer of material about 30 nm thick at the valleys and 65–130 nm thick at the top of the crests, which melts and solidifies forming NiTi with an amorphous structure. A layer of ablation debris composed of amorphous NiTi nanoparticles was redeposited on the LIPSS crests. The results achieved indicate that the periodic variation of the absorbed radiation intensity leads to a variation of the predominant ablation mechanisms and, consequently, of the ablation rate, thus explaining the rippled surface topography. The comparison with theoretical predictions suggests that in the intensity maxima (corresponding to the valleys) the material is removed by liquid spallation, while at its minima (the crests) the predominant material removal mechanism is melting and vaporization. These results support Sipe et al LIPSS formation theory and are in contradiction with the theories that explain the formation of LIPSS by convective fluid flow or self-organized mass transport of a laser-induced instability.

1 January 2014 in Applied Surface Science
Verified
Journal Article
Closed access
RVR. Vilar
R. Vilar
SSS.P. Sharma
S.P. Sharma
Amelia AlmeidaAmelia Almeida
Amelia Almeida
LCLiliana Cangueiro
Liliana Cangueiro
VOVitor Oliveira
Vitor Oliveira


20 October 2021 in Molecules
Verified
Journal Article
Open access
PDF file
LCLiliana Cangueiro
Liliana Cangueiro
JCJose Antonio Ramos de Campos
Jose Antonio Ramos de Campos
DBDavid Bruneel
David Bruneel
Ultrafast lasers micromachining results depend on both the processing parameters and the material properties. The obtained thermal effects are negligible if a good combination of processing parameters is chosen. However, optimizing the processing parameters leading to the required surface quality on a given material can be quite complex and time consuming. We developed a semi-empirical model to estimate the heat accumulation on a surface as a function of the laser fluence, scanning speed and repetition rate. The simulation results were correlated with experimental ones on different materials, and compared with the transient temperature distributions calculated using an analytical solution to the heat transfer equation. The predictions of the proposed model allow evaluating the heat distribution on the surface, as well as optimizing the ultrafast laser micromachining strategy, yielding negligible thermal damage.