In this study, the impact of oscillatory fluids on the flow induced by afterbody vortices, resembling those of a high-speed train, was investigated in wind tunnel experiments. The afterbody vortices were generated by a cylindrical model with a slanted base at Reynolds numbers ranging from 87 000 to 200 000. A fluidic oscillator was utilized to produce sweeping jets (SWJ) acting on the vortical flow, which is similar to those observed over the rear of a typical high-speed train. Our particle image velocimetry measurements on cross-stream planes reveal that the oscillatory flow produced by the sweeping jet significantly reduces the magnitude of induced flow, resulting in a 17.7% and 15.9% decrease in the total velocity and horizontal slipstream, respectively, at a velocity ratio of 6.4. This is attributed to the injection of the kinetic energy of sweeping jets into the core of the afterbody vortices, which leads to a higher dispersion of vorticity and incoherent energy distributions. The iso-surfaces of resultant velocities reveal that the fluid injection by the sweeping jet increased local velocities, resulting in a spanwise shrinkage of the induced velocity structure downstream. The study demonstrates the capability of sweeping jets in decreasing induced flow by manipulating afterbody vortices and their potential for reducing the slipstream produced by high-speed trains at the tracksides.
In this work, a pair of sweeping jet actuators is installed underneath the endplate of a slanted-base cylinder at ReD = 200 000. The sweeping jets form a 30° inclined angle with the endplate and are placed at different streamwise locations, and their strength is varied with a momentum coefficient, Cμ, ranging from 3.8 × 10−3 to 6.0 × 10−2. For all the cases examined in this paper, it is found that while a higher Cμ produces a higher drag reduction, the flow control energy efficiency decreases rapidly as Cμ increases. A net energy saving is achieved when Cμ is less than 0.01, and the highest energy efficiency obtained in the present study is 2.8% when the actuator pair is placed at the most upstream location tested. The drag reduction is attributed to the reaction force and an increase in the surface pressure force acting on the endplate produced by the jet pair. The contribution from the former constitutes an increasing proportion of the total drag reduction as Cμ increases leading to lower energy efficiency in flow control. Depending on the relative positions between the trajectory of the sweeping jet and afterbody vortex, sweeping jets are not only capable of altering the surface pressure distributions via directly imposing a footprint of high pressure on the surface, but also affecting the roll-up of the afterbody vortex and/or reducing its strength via injecting turbulence into the afterbody vortex.
A diversion slot is one of the potential mechanical devices to reduce high-speed train underbody aerodynamic resistance. This research aims to investigate the effectiveness of using diversion slots as a means of passive flow control to reduce the resistance of a high-speed train. Two different diversion slot designs, i.e., the big diversion slot (Bds) and the small diversion slot (Sds), placed at two installation locations near the bogie cabin end walls in six configurations are used. The results indicate that drag of the tail car is significantly reduced by 7.8%, 5.5%, 9.0%, and 9.4% using the configurations in cases 2 and 4–6, while an increase in 0.4% is experienced in case 3. Consequently, the total train aerodynamic resistance reduces by 1.9%, 0.2%, 3.0%, 4.2%, and 0.4% in cases 2–6, respectively, as compared to case 1. By evaluating the flow structure, we found that the diversion slots trigger flow separation, deflecting the airflow from entering the bogie regions, increasing flow turbulence and reducing the flow velocity. It efficiently improves the wake flow structure by reducing the wake strength, thereby increasing the tail nose surface pressure, thus reducing the tail car's aerodynamic drag. This study proposes a novel approach for reducing aerodynamic drag in high-speed trains, improving the underbody flow and wake characteristics.
In this paper, a sweeping jet is applied to control the afterbody vortices behind a slanted-base cylinder for the first time at Reynolds numbers from 87 000 to 200 000. The control effects are examined using stereo particle image velocimetry and surface pressure measurements with the jet momentum coefficient (Cμ) varying from 0.056 to 0.893. It is found that the sweeping jet results in increasingly diffused and larger afterbody vortices as Cμ increases. While an increase in Cμ up to 0.167 leads to a reduction in the circulation of the afterbody vortices and their earlier detachment from the slanted base, a further increase in Cμ introduces additional vorticity into the afterbody vortices leading to higher vortex strength, which could be detrimental to the control purpose. The interaction mechanism of sweeping jets lies in that turbulence is injected into the afterbody vortices as the sweeping jet intersects with these vortices and this subsequently causes diffusion of velocity gradient in the vortices, which weakens their strength. As the sweeping jet spreads itself sideways, while it propagates downstream along the endplate, it pushes the afterbody vortices upward and to the side. The impact of the sweeping jet has resulted in the dominant vortex wandering frequency of the afterbody vortex being locked to that of the sweeping jet. This also causes the afterbody vortices detach themselves from the endplate earlier resulting in a shorter low-pressure footprint on the surface.