Polyoxymethylene (POM) is one of the most popular thermoplastic polymers used in the industry. Therefore, the interest in its potential applications in rapid prototyping is understandable. Nevertheless, its low dimensional stability causes the warping of 3D prints, limiting its applications. This research aimed to evaluate the effects of POM modification with ethylene-vinyl acetate (EVA) (2.5, 5.0, and 7.5 wt.%) on its processing (by melt flow index), structure (by X-ray microcomputed tomography), and properties (by static tensile tests, surface resistance, contact angle measurements, differential scanning calorimetry, and thermogravimetric analysis), as well as very rarely analyzed emissions of volatile organic compounds (VOCs) (by headspace analysis). Performed modifications decreased stiffness and strength of the material, simultaneously enhancing its ductility, which simultaneously increased the toughness even by more than 50% for 7.5 wt.% EVA loading. Such an effect was related to an improved linear flow rate resulting in a lack of defects inside the samples. The decrease of the melting temperature and the slight increase of thermal stability after the addition of EVA broadened the processing window for 3D printing. The 3D printing trials on two different printers showed that the addition of EVA copolymer increased the possibility of a successful print without defects, giving space for further development.

The etiological agents of babesiosis are intraerythrocytic parasites of the genus Babesia, which are transmitted by ticks. The course of disease is characterized by variable severity. The risk of a complicated course of babesiosis occurs in premature infants, the elderly, splenectomized patients and other immunocompromised patients. Severe cases of this disease can lead to multiple organ dysfunction. The study focuses on the impact assessment of chronic Babesia microti invasion on the morphology and ultrastructure of rat liver. The analyzed material was comprised of liver samples collected from Wistar rats infected with a reference strain of B. microti (ATCC 30221). None of the livers collected from rats with babesiosis was enlarged. The histopathological analyses showed signs of intensive inflammatory processes, especially in the perivascular areas. The hepatic mononuclear phagocyte system was characterized by increased activity. The ultrastructral analyses confirmed disintegration of hepatocytes with vacuolization in the perivascular areas. In addition, the perisinusoidal space (space of Disse) had irregular structure. In some areas, the space of Disse was enlarged or compressed. The morphological and ultrastructural analyses of rat liver with chronic babesiosis caused by B. microti showed significant pathological changes in perivascular areas which may be the cause of hepatic dysfunction.

Tick-borne diseases (TBDs) have become a popular topic in many medical journals. Besides the obvious participation of ticks in the transmission of pathogens that cause TBD, little is written about alternative methods of their spread. An important role is played in this process by mammals, which serve as reservoirs. Transplacental transfer also plays important role in the spread of some TBD etiological agents. Reservoir species take part in the spread of pathogens, a phenomenon that has extreme importance in synanthropic environments. Animals that accompany humans and animals migrating from wild lands to urban areas increase the probability of pathogen infections by ticks This article provides an overview of TBDs, such as tick-borne encephalitis virus (TBEV), and TBDs caused by spirochetes, α-proteobacteria, γ-proteobacteria, and Apicomplexa, with particular attention to reports about their potential to cross the maternal placenta. For each disease, the method of propagation, symptoms of acute and chronic phase, and complications of their course in adults, children, and animals are described in detail. Additional information about transplacental transfer of these pathogens, effects of congenital diseases caused by them, and the possible effects of maternal infection to the fetus are also discussed. The problem of vertical transmission of pathogens presents a new challenge for medicine. Transfer of pathogens through the placenta may lead not only to propagation of diseases in the population, but also constitute a direct threat to health and fetal development. For this reason, the problem of vertical transmission requires more attention and an estimation of the impact of placental transfer for each of listed pathogens.

Purpose: Xenotransplantations of porcine cells, tissues, and organs involve a risk of zoonotic viral infections in recipients, including by porcine endogenous retroviruses (PERVs), which are embedded the genome of all pigs. An appropriate preparation of porcine heart valves for transplantation can prevent retroviral infection. Therefore, the present study focuses on the effect of epoxy compounds and glutaraldehyde on the PERV presence in porcine heart valves prepared for clinical use. Methods: Porcine aortic heart valves were fixed with ethylene glycol diglycidyl ether (EDGE) at 5°C and 25°C as well as with glutaraldehyde (GA) for 4 weeks. Salting out was used to isolate genomic DNA from native as well as EDGE- and GA-fixed fragments of valves every week. Quantification of PERV-A, PERV-B, and PERV-C DNA was performed by real-time quantitative polymerase chain reaction (QPCR). Results: All subtypes of PERVs were detected in native porcine aortic heart valves. The reduction of the PERV-A, PERV-B, and PERV-C DNA copy numbers was observed in the heart valves which were EDGE-fixed at both temperatures, and in GA-fixed ones in the following weeks. After 7 and 14 days of EDGE cross-linking, significant differences between the investigated temperatures were found for the number of PERV-A and PERV-B copies. PERV DNA was completely degraded within the first week of EDGE fixation at 25°C. Conclusions: EDGE fixation induces complete PERV genetic material degradation in porcine aortic heart valves. This suggests that epoxy compounds may be alternatively used in the preparation of bioprosthetic heart valves in future.

The aim of this study was to quantitatively evaluate alloplastic Temporomandibular Joint (TMJ) Prostheses against other treatment modalities regarding the jaw kinematics. Six patients with Temporomandibular Joint Prostheses, four with mandibular ramus Patient-Specific Implant (PSI) with condylar head preservation, and four after mandibular condylectomy were evaluated by the means of axiography (Cadiax Compact 2), which is the noninvasive three-dimensional study of condylar movements. The patients were also evaluated clinically for the mandibular movements. The study revealed that the significant movement limitations occurred bilaterally in patients fitted with TMJ prosthesis. For the protrusion movement, the vector length of the movement (L) for the TMJ prosthesis was 0.31 vs. 3.01 mm for the PSI (Kruskal–Wallis chi-squared = 9.1667, df = 2, p-value = 0.01022, post hoc Dunn p-value = 0.015) and for the laterotrusion to the operated side, the length of the vector (L) was 0.66 vs. 3.35 mm, respectively. Statistically significant differences between groups were most frequent for the laterotrusion to the unoperated side. The study shows that a further development on TMJ Prostheses geometry and materials is needed.

In the era of modern medicine, the number of invasive treatments increases. Artificial devices used in medicine are associated with an increased risk of secondary infections. Bacterial biofilm development observed on the implanted surface is challenging to treat, primarily due to low antibiotics penetration. In our study, the preparation of a new polycarbonate composite, filled with nanosilver, nanosilica and rhodamine B derivative, suitable for three-dimensional printing, is described. Polymer materials with antimicrobial properties are known. However, in most cases, protection is limited to the outer layers only. The newly developed materials are protected in their entire volume. Moreover, the antibacterial properties are retained after multiple high-temperature processing were performed, allowing them to be used in 3D printing. Bacterial population reduction was observed, which gives an assumption for those materials to be clinically tested in the production of various medical devices and for the reduction of morbidity and mortality caused by multidrug-resistant bacteria.