Growing environmental concerns and the need for better power balancing and frequency control have increased attention in renewable energy sources such as the reversible pump-turbine which can provide both power generation and energy storage. Pump-turbine operation along the S-shaped curve can lead to difficulties in loading the rejection process with unusual increases in water pressure, which lead to machine vibrations. Pressure fluctuations are the primary reason for unstable operation of pump-turbines. Misaligned guide vanes (MGVs) are widely used to control the stability in the S region. There have been experimental investigations and computational fluid dynamics (CFD) simulations of scale models with aligned guide vanes and MGVs with spectral analyses of the S curve characteristics and the pressure pulsations in the frequency and time-frequency domains at runaway conditions. The course of the S characteristic is related to the centrifugal force and the large incident angle at low flow conditions with large vortices forming between the guide vanes and the blade inlets and strong flow recirculation inside the vaneless space as the main factors that lead to the S-shaped characteristics. Preopening some of the guide vanes enables the pump-turbine to avoid the influence of the S characteristic. However, the increase of the flow during runaway destroys the flow symmetry in the runner leading to all asymmetry forces on the runner that leads to hydraulic system oscillations. The MGV technique also increases the pressure fluctuations in the draft tube and has a negative impact on stable operation of the unit.

Current research on pump-turbine units is focused on the unstable operation at off-design conditions, with the characteristic curves in generating mode being S-shaped. Unlike in the traditional water turbines, pump-turbine operation along the S-shaped curve can lead to difficulties during load rejection with unusual increases in the water pressure, which leads to machine vibrations. This paper describes both model tests and numerical simulations. A reduced scale model of a low specific speed pump-turbine was used for the performance tests, with comparisons to computational fluid dynamics(CFD) results. Predictions using the detached eddy simulation(DES) turbulence model, which is a combined Reynolds averaged Naviers-Stokes(RANS) and large eddy simulation(LES) model, are compared with the two-equation turbulence mode results. The external characteristics as well as the internal flow are for various guide vane openings to understand the unsteady flow along the so called S characteristics of a pump-turbine. Comparison of the experimental data with the CFD results for various conditions and times shows that DES model gives better agreement with experimental data than the two-equation turbulence model. For low flow conditions, the centrifugal forces and the large incident angle create large vortices between the guide vanes and the runner inlet in the runner passage, which is the main factor leading to the S-shaped characteristics. The turbulence model used here gives more accurate simulations of the internal flow characteristics of the pump-turbine and a more detailed force analysis which shows the mechanisms controlling of the S characteristics.

A vertical centrifugal pump with a vaned diffuser is very attractive in the field of long-distance water supply. Excessive pressure fluctuations in the vaneless region due to rotor–stator interaction (RSI) need careful evaluation. In the present investigation, the hydraulic performance and pressure fluctuation characteristics of a vertical centrifugal pump with three different lean modes of the blade trailing edge were quantitatively analyzed by comparison experiments, using the same test rig. Results showed that the pressure fluctuation level was the highest in the vaneless region, closest to the volute tongue, and increased as the flow rate deviated from the design flow rate. The lean mode of the blade trailing edge was found to have a slight influence on hydraulic performance, and the relative deviation of experimental specific speeds with three different lean modes was within 6%. The influence of the lean mode of the blade trailing edge on the pressure fluctuation level was experimentally verified for the first time. In particular, the flow rate-averaged peak-to-peak value of pressure fluctuation with the positive lean mode (PLM) was 62% of the corresponding value with the zero lean mode (ZLM), while no significant improvement was observed for the negative lean mode (NLM). The flow mechanism behind this may be explained as a weakening of the jet-wake flow pattern with PLM.

A large-scale, vaned-voluted centrifugal pump can be applied as the key component in water-transfer projects. Pressure pulsation will be an important factor in affecting the operation stability. This paper researches the propagation and spatial distribution law of blade passing frequency (BPF) and its harmonics on the design condition by numerical simulation. Experimental and numerical monitoring is conducted for pressure pulsation on four discrete points in the vaneless region, which shows that the BPF is dominant. The pulsation tracking network (PTN) is applied to research propagation law and spatial distribution law. It provides a reference for frequency domain information and visualization vaned diffuser. The amplitude of BPF and its harmonics decays rapidly in the vaneless region. BPF and BPF’s harmonics influence each other. BPF has local enhancement in the vaneless region when its harmonics attenuate. In the vaned diffuser, the pulsation amplitude of BPF attenuates rapidly, but the local high-pressure pulsation amplitude can be found on the vane blade concave side because of obstruction and accumulation of the vaned diffuser. In the volute, the pulsation amplitude of BPF is low with the decelerating attenuation. This study provides an effective method for understanding the pressure pulsation law in turbomachinery and other engineering flow cases.

In general, weak compressibility is one of the properties of liquids. That is, in actual operation of hydraulic machinery, the flow is weakly compressible. However, the influence of weak compressibility is often neglected in usual numerical simulation, which makes the simulation results different from the experimental results. Based on the Computational Fluid Dynamics (CFD) solver and model test rig, by means of mutual verification between numerical simulation and experiment, the fitting degree between numerical results and experimental results before and after considering weak compressibility is compared and analyzed in this paper; it is obtained that the numerical results is closer to the experimental results after considering the weak compressibility. In addition, velocity field of pump turbines, head loss of main components, and the change of entropy yield are analyzed and reasons for numerical value being closer to the experimental value after considering weak compressibility of fluid are summarized and analyzed. It is proved that the consideration of weak compressibility is of great significance to improve the accuracy of results in the numerical simulation of pump turbines.