A novel surface plasmon resonance (SPR) sensor with graphene and subwavelength gratings is proposed to improve the sensing performance. A series of numerical analyses were performed to investigate the effect of structural parameters on the sensing performance, such as minimum reflectance at resonance (MRR), full width at half maximum (FWHM), and resonance angle. The results indicated that near-zero MRR (2.9 × 10⁻⁶) and narrow FWHM (about 3.5 deg) could be obtained by optimizing the geometrical parameters. Moreover, the influence of the number of graphene layers on sensitivity was also studied. The maximum sensitivity of the designed sensor could reach 192 deg/refractive index unit (RIU), which is a great enhancement compared to the silver-only SPR sensor. In addition, ethylene glycol solutions with different refractive indices were detected. The results showed that the sensitivity of the sensor could reach 220.67 deg/RIU, and the proposed sensor had excellent linearity between the resonance angle and refractive index, enabling extensive potential practical sensing applications.

In recent years, the development of metamaterials and metasurfaces has drawn great attention, enabling many important practical applications. Focusing and lensing components are of extreme importance because of their significant potential practical applications in biological imaging, display, and nanolithography fabrication. Metafocusing devices using ultrathin structures (also known as metasurfaces) with superlensing performance are key building blocks for developing integrated optical components with ultrasmall dimensions. In this article, we review the metamaterial superlensing devices working in transmission mode from the perfect lens to two-dimensional metasurfaces and present their working principles. Then we summarize important practical applications of metasurfaces, such as plasmonic lithography, holography, and imaging. Different typical designs and their focusing performance are also discussed in detail.

In this paper, a novel D-shaped photonic crystal fiber sensor for simultaneous measurements of magnetic field and temperature is proposed and characterized. Based on the surface plasmon resonance theory, the D-shaped flat surface coated with a gold layer is in direct contact with magnetic fluid to detect magnetic field, and one of the relatively small air holes near the fiber core is filled with polydimethylsiloxane (PDMS) to sense temperature. The realization of measuring the magnetic field and temperature separately through two channels depends on the fact that the magnetic field only changes the refractive index of the magnetic fluid, but has no effect on the refractive index of PDMS. The refractive index of the magnetic fluid and PDMS can be affected by temperature at the same time. The sensor designed in this work can separate the variations of the magnetic field and temperature simultaneously, therefore solving the cross-sensitivity problem to further improve the magnetic field sensitivity. When the thickness of the gold film is 50 nm and the radius of the filling hole is 0.52 µm, the magnetic field sensitivity and the temperature sensitivity of magnetic field sensor based on temperature self-reference can reach 0.14274 nm/Oe and −0.229 nm/°C, respectively.

Super-resolution optical imaging is a consistent research hotspot for promoting studies in nanotechnology and biotechnology due to its capability of overcoming the diffraction limit, which is an intrinsic obstacle in pursuing higher resolution for conventional microscopy techniques. In the past few decades, a great number of techniques in this research domain have been theoretically proposed and experimentally demonstrated. Graphene, a special two-dimensional material, has become the most meritorious candidate and attracted incredible attention in high-resolution imaging domain due to its distinctive properties. In this article, the working principle of graphene-assisted imaging devices is summarized, and recent advances of super-resolution optical imaging based on graphene are reviewed for both near-field and far-field applications.

In this work, a surface plasmon resonance (SPR) sensor based on a novel liquid-core polymer optical fiber (POF) is proposed and numerically analyzed for refractive index (RI) detection. The polytetrafluoroethylene (PTFE) fiber is selected as the platform for SPR sensing. We combine the PTFE-based POF with the liquid-core structure by introducing a hole filled with analyte into the fiber center. The hole also acts as the fiber core to guide the incident light. This design helps to realize the detection of solutions with low RI values (around 1.33), while keeping the distinguished sensing characteristics of the liquid-core structure. Two side air holes are introduced into the cladding and a thin silver film protected by a titanium dioxide layer is plated on the wall of one air hole, which helps to control the mode coupling. In order to optimize the design of this sensor, the impacts of parameters such as metal layer thicknesses and the central hole radius are investigated using the full-vector finite element method (FEM). After optimization, our design shows a wavelength interrogation sensitivity reaching up to 16,750 nm/RIU and an average full-width at half-maximum (FWHM) of 42.86 nm in the RI range of 1.325–1.35.

Hyperlensing devices have drawn great attention in recent years due to their ability to amplify the subwavelength image of objects with more detail and information. In this work, a hyperlens with a radian inner surface is designed and demonstrated. The proposed hyperlens is capable of imaging different types of sub-wavelength objects efficiently. Plasmonic resonant cavity is also employed in order to achieve a super-resolution imaging effect. Different objects are investigated to test the performance of the proposed hyperlens. As expected, our hyperlens shows better tolerance than the conventional hyperlensing designs and can achieve imaging resolution down to 60 nm for different types of objects.