Nino Dakov

Dr. Nino Dakov

Trelleborg Sealing Solutions
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 September 2021 in Tribology Transactions
Verified
Journal Article
Closed access
MAMario
Mario
STStoll
Stoll
Nino DakovNino Dakov
Nino Dakov
MGMarco Gohs
Marco Gohs
FBFrank Bauer
Frank Bauer
Due to increasingly stringent environmental regulations, leakage-free shaft seals with minimal friction are growing ever more important. The trend toward higher operating speed (e.g., in the field of e-mobility) additionally aggravates the sealing task. Reliable, leakage-free shaft seals—such as gas-lubricated mechanical seals—are difficult to manufacture and thus expensive. Therefore, there is still significant interest in an efficient and easy-to-manufacture shaft seal design. This study discusses the development of sleeve-type lip seals made of fluoroelastomer with an innovative, sickle-shaped back-structure design. The novel lip seals are capable of operating at near-zero friction. Compared to state-of-the-art, gas-lubricated mechanical seals, near-frictionless sliding on an air film is achieved with a simple, robust, and easy-to-manufacture sealing-lip design.

16 September 2021 in Lubricants
Verified
Journal Article
Open access
PDF file
Oliver FeuchtmüllerOliver Feuchtmüller
Oliver Feuchtmüller
Nino DakovNino Dakov
Nino Dakov
LHLothar Hörl
Lothar Hörl
FBFrank Bauer
Frank Bauer
The oil film generation of a U-cup rod seal and the oil film thickness on the rod after outstroke were analyzed analytically, numerically, and experimentally. The analyzed sealing system consists of an unmodified, commercially available U-cup, a polished rod, and mineral oil. The inverse theory of hydrodynamic lubrication (IHL) and an elastohydrodynamic lubrication (EHL) model—both based on the Reynolds equation for thin lubricating films—were utilized to simulate the oil film generation. In the EHL analysis, physical parameters and numerical EHL parameters were varied. Both the analytical and numerical results for the varied parameters show that the film thickness follows a square-root function (i.e., with a function exponent of 0.5) with respect to the product of dynamic viscosity and rod speed, also referred to as the duty parameter. In comparison to the analytical and numerical results, the film thickness obtained via ellipsometry measurements is a function of the duty parameter with an exponent of approximately 0.85. Possible causes for the discrepancy between theory and experiments are discussed. A potential remedy for the modeling gap is proposed.

15 December 2019 in Tribology Online
Verified
Journal Article
Open access
PDF file
Nino DakovNino Dakov
Nino Dakov
SFSimon Feldmeth
Simon Feldmeth
MSMario Stoll
Mario Stoll
FBFrank Bauer
Frank Bauer
Lip seals made of PTFE compound are used due to their high thermal and chemical stability for the sealing of shaft interfaces in housings. For a better dynamic leak-tightness hydrodynamic sealing aids are manufactured on the sealing lip. Thus a PTFE lip seal is capable of back-pumping fluid from the air to the fluid side. The pumping rate serves as an important parameter for the dynamic leaktightness of seals with a unidirectional sealing aid design. The correlation of pumping rate and dynamic leak-tightness for bi-directional sealing aid designs is deficient. A new hydrodynamic parameter is introduced to assess the dynamic leak-tightness of a sealing aid design. The so called pressure drag is the force resulting from the integral of the hydrodynamic pressure over the surface of the sealing aid. A hypothesis is proposed, stating that in order to guarantee a dynamically leak-tight shaft seal, two conditions should be satisfied. First, the pumping rate should be greater than zero. Second, the axial pressure drag should be directed entirely towards the fluid side. The hypothesis is verified on different types of unidirectional and bi-directional sealing aid design. In conclusion the axial pressure drag is shown to be a suitable performance parameter for the sealing aid design.

1 January 2022
Verified
Conference Paper
Closed access
Nino DakovNino Dakov
Nino Dakov
TGTrelleborg Sealing Solutions Germany
Trelleborg Sealing Solutions Germany
CSChristoph Schuele
Christoph Schuele

1 September 2024
Verified
Conference Paper
Closed access
TGTrelleborg Sealing Solutions Germany
Trelleborg Sealing Solutions Germany
Nino DakovNino Dakov
Nino Dakov
MFMartin Franz
Martin Franz
JBJeff Baehl
Jeff Baehl
TATrelleborg Sealing Solutions Americas
Trelleborg Sealing Solutions Americas
SWSam Wagoner
Sam Wagoner
High-pressure radial shaft seals are typically used in hydraulic pumps to seal a continuously rotating shaft within a housing bore. When the seal is pressurized, the sealing lip’s contact with the shaft increases, which leads to higher wear. At very high pressures, the seal’s cross-section can collapse, forcing the garter spring out of its retaining groove. This issue can be mitigated by stiffening the membrane area, though this reduces the seal’s ability to accommodate radial movement of the shaft. The current study presents a new approach to stabilize the seal’s cross-section. Multiple pads are added on the seal above the membrane area and next to the spring. As a result, a considerably lower laydown is achieved, resulting in improved wear performance during tests. Additionally, the pads help maintain the spring’s position. The theoretical considerations are supported by tests conducted under varying pressure and shaft speed conditions, demonstrating the practical benefits of this new seal design.

1 September 2026
Verified
Conference Paper
Closed access
PBPeter Bauer
Peter Bauer
Nino DakovNino Dakov
Nino Dakov
MFMartin Franz
Martin Franz