Sushanta Ghoshal

Dr. Sushanta Ghoshal

Polymer Scientist
orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2015 in Carbon
Verified
Journal Article
Closed access
HCHan Gi Chae
Han Gi Chae
BNBradley A. Newcomb
Bradley A. Newcomb
PGPrabhakar V. Gulgunje
Prabhakar V. Gulgunje
YLYaodong Liu
Yaodong Liu
KGKishor K. Gupta
Kishor K. Gupta
SKSatish Kumar
Satish Kumar

23 October 2017 in Fibers
Verified
Journal Article
Open access
PDF file
Sushanta GhoshalSushanta Ghoshal
Sushanta Ghoshal
Additive manufacturing (AM)/3D printing (3DP) is a revolutionary technology which has been around for more than two decades, although the potential of this technique was not fully explored until recently. Because of the expansion of this technology in recent years, new materials and additives are being searched for to meet the growing demand. 3DP allows accurate fabrication of complicated models, however, structural anisotropy caused by the 3DP approaches could limit robust application. A possible solution to the inferior properties of the 3DP based materials compared to that of conventionally manufactured counterparts could be the incorporation of nanoparticles, such as carbon nanotubes (CNT) which have demonstrated remarkable mechanical, electrical, and thermal properties. In this article we review some of the research, products, and challenges involved in 3DP technology. The importance of CNT dispersion in the matrix polymer is highlighted and the future outlook for the 3D printed polymer/CNT nanocomposites is presented.

21 July 2011 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
PDF file
SNS. Nahar
S. Nahar
RKRuhul Khan
Ruhul Khan
KDK. Dey
K. Dey
BSB. Sarker
B. Sarker
ADA.K. Das
A.K. Das
Sushanta GhoshalSushanta Ghoshal
Sushanta Ghoshal
Jute and bamboo fiber-reinforced polypropylene (PP) based composites (50 wt% fiber) were fabricated by compression molding. Tensile strength (TS), bending strength (BS), tensile modulus (TM), and bending modulus (BM) of the jute-reinforced PP composite were found to be 48, 56, 900, and 1500 MPa, respectively. Then, bamboo fiber-reinforced PP-based composites (50 wt% fiber) were fabricated and the mechanical properties evaluated. The TS, BS, TM, and BM of bamboo-reinforced PP composites were found to be 60, 76, 4210, and 6210 MPa, respectively. It was revealed that bamboo fiber-based composites had higher TS, BS, TM, and BM compared to jute-based composites. Degradation tests of the composites (jute fiber/PP and bamboo fiber/PP) were performed in soil at ambient conditions for up to 24 weeks. It was revealed that bamboo fiber/PP composite retained its original mechanical properties higher than that of jute fiber/PP composite. The interfacial shear strength of the jute and bamboo fiber-based composites was investigated using the single-fiber fragmentation test and it was found to be 2.14 and 4.91 MPa, respectively. Fracture sides of the composites were studied by scanning electron microscope, and the results revealed poor fiber matrix adhesion for jute fiber-based composites compared to that of the bamboo fiber-based composites.

15 February 2012 in Macromolecules
Verified
Journal Article
Closed access
Sushanta GhoshalSushanta Ghoshal
Sushanta Ghoshal
PDPaul Denner
Paul Denner
SSSiegfried Stapf
Siegfried Stapf
CMCarlos Mattea
Carlos Mattea

1 September 2016 in Polymer
Verified
Journal Article
Closed access
Sushanta GhoshalSushanta Ghoshal
Sushanta Ghoshal
PWPo-Hsiang Wang
Po-Hsiang Wang
PGPrabhakar Gulgunje
Prabhakar Gulgunje
NVNikhil Verghese
Nikhil Verghese
SKSatish Kumar
Satish Kumar

1 September 2016 in Polymer
Verified
Journal Article
Closed access
PWPo-Hsiang Wang
Po-Hsiang Wang
Sushanta GhoshalSushanta Ghoshal
Sushanta Ghoshal
PGPrabhakar Gulgunje
Prabhakar Gulgunje
NVNikhil Verghese
Nikhil Verghese
SKSatish Kumar
Satish Kumar