Au-hyperdoped Si absorbs near-infrared (NIR) light and recent efforts have successfully produced Si-based NIR photodetectors based on this property but with low detection efficiencies. Here, we investigate the differences between the optical and photocurrent properties of Au-hyperdoped Si. Although defects introduced during fabrication of these materials may not exhibit significant optical absorption, we show that they can produce a measurable photocurrent under NIR illumination. Our results indicate that the optimal efficiency of impurity-hyperdoped Si materials is yet to be achieved and we discuss these opportunities in light of our results. This work thus represents a step forward in demonstrating the viability of using impurity-hyperdoped Si materials for NIR photodetection.
Spins in silicon that are accessible via a telecom-compatible optical transition are a versatile platform for quantum information processing that can leverage the well-established silicon nanofabrication industry. Key to these applications are long coherence times on the optical and spin transitions to provide a robust system for interfacing photonic and spin qubits. Here, we report telecom-compatible Er3+ sites with long optical and electron spin coherence times, measured within a nuclear spin-free silicon crystal (<0.01 % 29Si) using optical detection. We investigate two sites and find 0.1 GHz optical inhomogeneous linewidths and homogeneous linewidths below 70 kHz for both sites. We measure the electron spin coherence time of both sites using optically detected magnetic resonance and observe Hahn echo decay constants of 0.8 ms and 1.2 ms at ~ 11 mT. These optical and spin properties of Er3+:Si are an important milestone towards using optically accessible spins in silicon for a broad range of quantum information processing applications.
Over four decades ago, pulsed-laser melting, or pulsed-laser annealing as it was termed at that time, was the subject of intense study as a potential advance in silicon device processing. In particular, it was found that nanosecond laser melting of the near-surface of silicon and subsequent liquid phase epitaxy could not only very effectively remove lattice disorder following ion implantation, but could achieve dopant electrical activities exceeding equilibrium solubility limits. However, when it was realised that solid phase annealing at longer time scales could achieve similar results, interest in pulsed-laser melting waned for over two decades as a processing method for silicon devices. With the emergence of flat panel displays in the 1990s, pulsed-laser melting was found to offer an attractive solution for large area crystallisation of amorphous silicon and dopant activation. This method gave improved thin film transistors used in the panel backplane to define the pixelation of displays. For this application, ultra-rapid pulsed laser melting remains the crystallisation method of choice since the heating is confined to the silicon thin film and the underlying glass or plastic substrates are protected from thermal degradation. This article will be organised chronologically, but treatment naturally divides into the two main topics: (1) an electrical doping research focus up until around 2000, and (2) optical doping as the research focus after that time. In the first part of this article, the early pulsed-laser annealing studies for electrical doping of silicon are reviewed, followed by the more recent use of pulsed-lasers for flat panel display fabrication. In terms of the second topic of this review, optical doping of silicon for efficient infrared light detection, this process requires deep level impurities to be introduced into the silicon lattice at high concentrations to form an intermediate band within the silicon bandgap. The chalcogen elements and then transition metals were investigated from the early 2000s since they can provide the required deep levels in silicon. However, their low solid solubilities necessitated ultra-rapid pulsed-laser melting to achieve supersaturation in silicon many orders of magnitude beyond the equilibrium solid solubility. Although infrared light absorption has been demonstrated using this approach, significant challenges were encountered in attempting to achieve efficient optical doping in such cases, or hyperdoping as it has been termed. Issues that limit this approach include: lateral and surface impurity segregation during solidification from the melt, leading to defective filaments throughout the doped layer; and poor efficiency of collection of photo-induced carriers necessary for the fabrication of photodetectors. The history and current status of optical hyperdoping of silicon with deep level impurities is reviewed in the second part of this article.
We demonstrate that pulsed laser melting (PLM) of thin 1, 5, and 10 nm-thick vapor-deposited gold layers on silicon enhances its room-temperature sub-band gap infrared absorption, as in the case of ion-implanted and PLM-treated silicon. The former approach offers reduced fabrication complexity and avoids implantation-induced lattice damage compared to ion implantation and pulsed laser melting, while exhibiting comparable optical absorptance. We additionally observed strong broadband absorptance enhancement in PLM samples made using 5- and 10-nm-thick gold layers. Raman spectroscopy and Rutherford backscattering analysis indicate that such an enhancement could be explained by absorption by a metastable, disordered and gold-rich surface layer. The sheet resistance and the diode electrical characteristics further elucidate the role of gold-supersaturation in silicon, revealing the promise for future silicon-based infrared device applications.
The widefield diamond nitrogen-vacancy (NV) microscope is a powerful instrument for imaging magnetic fields. However, a key limitation impeding its wider adoption is its complex operation, in part due to the difficulty of precisely interfacing the sensor and sample to achieve optimum spatial resolution. Here, we demonstrate a solution to this interfacing problem that is practical and reliably minimizes NV-sample standoff. We built a compact widefield NV microscope, which incorporates an integrated widefield diamond probe with full position and angular control, and developed a systematic alignment procedure based on optical interference fringes. Using this platform, we imaged an ultrathin (1 nm) magnetic film test sample and conducted a detailed study of the spatial resolution. We reproducibly achieved an estimated NV-sample standoff (and hence spatial resolution) of at most across a field of view. Guided by these results, we suggest future improvements for approaching the optical diffraction limit. This work is a step toward realizing a widefield NV microscope suitable for routine high-throughput mapping of magnetic fields.
Hyperdoped Si formed by implantation followed by pulsed laser melting is a promising material for enhanced near-infrared photodetection. To realize the full potential of this material, it is crucial to understand the nature of defects arising from the fabrication process and how these may impact device operation. Here, we identify through deep level transient spectroscopy the presence of a range of defects in the substrate depletion layer that arise from interactions between high dose ion implantation and pulsed laser melting, and investigate their annealing behavior up to C. In particular, the detection of a vacancy complex with densities as high as indicates that optical transitions between this level and the valence band may compete with the Au donor center, and hence could potentially contribute to the photocurrent in hyperdoped photodiodes.