The state of Sonora, Mexico, stands as one of the leading producers of pecan nuts in the country, which are commercialized without shells, leaving behind this unused residue. Additionally, this region has abundant solar resources, as shown by its high levels of direct normal irradiance (DNI). This study contributes to research efforts aimed at achieving a synergy between concentrated solar energy technology and biomass pyrolysis processes, with the idea of using the advantages of organic waste to reduce greenhouse gas emissions and avoiding the combustion of conventional pyrolysis through the concentration of solar thermal energy. The objective of this study is to pioneer a new experimental analysis methodology in research on solar pyrolysis reactors. The two main features of this new methodology are, firstly, the comparison of temperature profiles during the heating of inert and reactive materials and, secondly, the analysis of heating rates. This facilitated a better interpretation of the observed phenomenon. The methodology encompasses two different thermal experiments: (A) the pyrolysis of pecan shells and (B) the heating–cooling process of the biochar produced in experiment (A). Additionally, an experiment involving the heating of volcanic stone is presented, which reveals the temperature profiles of an inert material and serves as a comparative reference with experiment (B). In this experimental study, 50 g of pecan shells were subjected to pyrolysis within a cylindrical stainless-steel reactor with a volume of 156 cm³, heated by concentrated radiation from a solar simulator. Three different heat fluxes were applied (234, 482, and 725 W), resulting in maximum reaction temperatures of 382, 498, and 674 °C, respectively. Pyrolysis gas analyses (H₂, CO, CO₂, and CH₄) and characterization of the obtained biochar were conducted. The analysis of heating rates, both for biochar heating and biomass pyrolysis, facilitated the identification, differentiation, and interpretation of processes such as moisture evaporation, tar production endpoint, cellulosic material pyrolysis, and lignin degradation. This analysis proved to be a valuable tool as it revealed heating and cooling patterns that were not previously identified. The potential implications of this tool would be associated with improvements in the design and operation protocols of solar reactors.

The radiation flux distributions produced by the concentrating solar systems used to produce thermal/electrical power are usually non-homogeneous. This results in non-uniform temperature distributions on the solar receivers, causing adverse effects on the system’s overall performance. An approach to better understand the problem is to study the surfaces around the focal zone where the radiation density is homogeneous (isosurfaces), generating them from experimental data. For this, it is necessary to superimpose built volumes of the different irradiance levels using parallel planes in different directions from the focal point of a concentrator. These volumes are known as effective volumes. This study presents the model used to generate effective volume produced by a point focus concentrator, comparing it with experimental results in a direction perpendicular to the focal axis. The effective volumes were developed considering a global optical error of the system of 2.8 mrad. The set of methods used to generate effective volumes has not been previously presented in the literature. The theoretical-experimental research consisted of the combination of the camera-target method and the simulations by the ray-tracing technique. The results showed effective volumes with the highest value of 10 MW/m² and the lowest value of 4.5 MW/m².

Este artículo presenta el estudio experimental que consiste en el análisis del desempeño térmico y eléctrico de un sistema HCPV que cuenta con dos discos parabólicos y sus respectivas unidades de conversión de potencia (PCUs) configurados en una óptica especial conocida como XRX-Köhler. Este sistema utiliza celdas multi-unión, que, a pesar de su alta eficiencia, no utilizan entre el 60-70% de la radiación recibida por lo que esta energía debe ser retirada con un sistema de enfriamiento para mantener su temperatura dentro de un intervalo que asegure su integridad y el mejor desempeño de la misma. A diferencia de las celdas de unión sencillas, las MJ pueden operar a más altas temperaturas con eficiencias aceptables de producción eléctrica. Esta característica de operar en un rango amplio de temperaturas (~ 90°C), puede hacer que sistemas térmicos de aplicaciones solares funcionen con el calor residual y así mejorar el desempeño total del sistema. Se ha desarrollado una serie de campañas de pruebas experimentales para la evaluación tanto de las curvas I-V en forma instantánea como las eficiencias instantáneas eléctrica y térmica obteniendo valores de ~24% y de ~53%, respectivamente.

This study reports the initial thermal and thermochemical performance of a novel solarized Auger-type reactor for Pyrolysis (SARP), specifically developed for the valorization of organic solid waste into solar-derived fuels. A key innovation of this system lies in its integration with a high-flux, point-focus solar concentrator that enables controlled delivery of concentrated solar radiation to drive endothermic processes. At the front of the reactor, the thermal evaluation under solar irradiation shows that surface temperatures reached up to approximately 750 °C on the exterior, while the hottest section of the interior briefly reached approximately 700 °C, in the pyrolysis zone. In contrast, the preheating zone inside the reactor exhibits temperatures ranging from 160 °C to 306 °C, indicating a non-uniform thermal profile for the incoming feedstock. The campaign focused on thermochemical pyrolysis, in which pecan walnut tree pruning residue biomass was processed under controlled semicontinuous operation. Batches of 600 g were pyrolyzed, yielding approximately 390 g of biochar and achieving a peak hydrogen concentration of 14.5% vol in the product gases. These findings demonstrate the reactor’s potential for solar-driven waste-to-fuel conversion.

A theoretical and experimental evaluation was conducted on a prototype radiative flux homogenizer (HOFRAC) specifically designed for the Solar Furnace at Instituto de Energías Renovables (HoSIER) of Universidad Nacional Autónoma de México. The development of HOFRAC included three versions (HOFRAC-PRO, HOFRAC-PRI, and HOFRAC-PRIK); each iteration incorporated improvements based on theoretical modeling and experimental results. Evaluations were performed using ray-tracing simulations and experimental tests capturing radiative flux distribution images. The last two versions were used to characterize a densely packed photovoltaic array operated in the solar furnace. Some results of this study show that misaligned mirrors in the furnace were identified as the main problem in achieving a high flux uniformity degree for photovoltaic concentration applications.