Home energy monitoring by appliance-level information can provide consumers awareness on energy saving. The system can be implemented through a smart meter which requires an efficient data analysis algorithm for providing an accurate energy consumption profile, the purpose for proper home energy management. This paper proposes a set of data analysis procedures for extracting appliances power state from its power consumption data. The approach is based on multitarget classification, a new data learning framework for nonintrusive load monitoring. The procedures include 1) partitioning the appliance power data into an effective number of power states using K-means clustering. 2) determining the optimal number of power states using the Area Under the ROC Curve index. The design objective is to obtain the optimal predictive performance for identification of the appliance power state which could result in a proper power and energy prediction. Applying the multitarget classification algorithm of RAndom k-labELsets by disjoint subsets with the decision tree, the identification of appliance power state achieved F-score and accuracy values greater than 89% for high-power loads such as A/C and water heater. The normalized error values of power prediction outperformed the use of Factorial Hidden Markov Model and binary state modeling system.
This research article reports a development on green pigments having high reflectance of NIR radiation from the sun. The aim of the development is to use the green pigments as a component of building paint to reduce heat penetrating into the building. Cr2O3, a green pigment oxide, was used as the host component and the mixtures of Al2O3, V2O5 and TiO2 were used as the guest components. Al2O3, V2O5 and TiO2 were mixed at different 36 compositions according to triaxial diagram. For each sample preparation, 80% wt Cr2O3 was mixed with 20%wt of guest component for each composition. Then the mixed sample were calcined at 1150 °C for 4 hours and were ground with an agate ball mill for 7 minutes at a speed of 250 rev/min. Finally, the pigments were sieved to obtain the particle sizes of 0.5 - 2.0 µm. The pigment powders were compressed in a mold to get samples in the form of thin disks, each one with a diameter of 2.7 cm and a thickness of 4 mm. The reflectance for all samples was measured using a spectrophotometer in the wavelength ranging from 300 – 2100 nm in accordance with ASTM E891. It was found that the maximum reflectance, in the wavelengths ranging from 780 – 2100 nm, of 82.83% was obtained from the sample with a composition of 80%Cr2O3, 14%Al2O3, 4%TiO2 and 2% V2O5.
Solar radiation in Thailand is abundant. Unfortunately, there is a large amount of non-direct solar radiation that could not be utilized by high concentrating photovoltaic (CPV) systems. This paper investigates the effect of diffuse radiation on a Fresnel-based CPV system using a secondary optical element (SOE) made of flat plate reflectors operating in Thailand. Physical experiments were conducted by constructing a simple SOE attached to commercial CPV components. Experimental results showed that the efficiency of the system with an SOE increased at least 10%. This increase in system efficiency is more significant with increasing diffuse solar radiation, i.e. the efficiency increased by 11-23% when the diffuse radiation ratios were 0.1–0.4, respectively. In a continuous operation, the energy gain from a CPV system with an SOE was 20% higher than the conventional system.
This paper describes a dataset for evaluating the effectiveness of energy disaggregation techniques, specifically Non-Intrusive Load Monitoring (NILM) algorithms. The dataset comprises real-world energy consumption data from a residential household in Bangkok, Thailand. It includes one aggregate circuit and ten active sub-circuits, including lights, plug-outlets, a water pump, a water heater, and an air conditioner, sampled at a one-minute interval. The dataset provides voltage, current, active power, reactive power, and power factor measurement data, facilitating experimentation with multiple energy disaggregation scenarios. The inclusion of the absolute and signed reactive power (Q) data allows greater flexibility in feature selection for model training. This dataset has been validated and utilized in previous research, demonstrating its robustness and high accuracy in appliance classification and power state detection. The data can also be applied to diagnose appliance faults and assess energy efficiency.
This work aimed to explore the possibility of producing NIR-reflective pigment from Thai leucoxene which is an abundant mineral consisting of ~89 wt.% TiO2, 6 wt.% SiO2 and 5 wt.% other oxides such as Al2O3 and Fe2O3. The leucoxene was purified by selective leaching of undesired oxides with NaOH under hydrothermal condition. Effects of NaOH concentration, hydrothermal temperature and time were investigated. The results revealed that dissolutions of the SiO2 and Al2O3 increased with an increased NaOH concentration, while that of the ZrO2 and Fe2O3 remained the same, resulting in the increased TiO2 concentration. The SiO2 dissolution also increased with an increased temperature and time. The optimum leaching condition, i.e. 4 M NaOH, 180 °C and 60 min, yielded TiO2 content of 93.94 ±0.14 wt.%. The Cr-doped CaTiO3 pigments (CaCrxTi1-xO3; x = 0, 0.025, 0.05, 0.75 and 0.1), synthesized from the purified leucoxene, CaO and Cr2O3 by solid-state reaction at 1100 °C, exhibited brown color hue and NIR reflectance in a range of 34.5−59.8% depending on the Cr content. At the Cr content of 0.05, the pigment exhibited decent brownish appearance and modest NIR reflectance of 50.7% which was close to that of the pigment synthesized from pure rutile. The glaze consisting of 10 wt.% pigment had a glossy light brown appearance, and possessed NIR reflectance of 75.0 %, indicating a promising application in a field of NIR-reflective coating.