Mehdi Hojjati

Dr. Mehdi Hojjati

Institute of Aerospace Design & Innovation, Concordia University, Montreal, QC H3G 1M8, Canada

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 April 2021 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
ARAlireza Rahimi
Alireza Rahimi
Mehdi HojjatiMehdi Hojjati
Mehdi Hojjati
Ali DolatabadiAli Dolatabadi
Ali Dolatabadi
Christian MoreauChristian Moreau
Christian Moreau
This paper reports a novel method for fabrication of an electro-thermal heating element, as de-icer or anti-icer, for the polymer-based composites. The plasma spray technique was utilized for the deposition of a Nickel-Chrome-Aluminum-Yttrium (NiCrAlY) coating layer as a heating element on top of the glass/epoxy composite. To improve the adhesion strength and deposition efficiency of the coatings and to protect the composite fibers during grit blasting and spraying, a woven wire stainless steel mesh was added to the composite substrates during the composite fabrication process. Metal mesh will act as an anchor to keep the coating on the surface. Two types of woven wire and two types of NiCrAlY powder with the fine and coarse particle size distributions were used. Good processing parameters for grit blasting and plasma spraying are identified. It is found that the surface modification method applied to the composite substrates prior to the coating process makes a significant improvement in the coating thickness uniformity and deposition efficiency. Several tests were conducted on the coated samples for determination of their mechanical and electrical properties. Using flatwise tensile tests, it is shown that application of proper surface modification method and set of spray parameters could result in improving the coating bonding strength significantly. The electrical and thermal analyses of the coated samples are also performed. It is shown that the coated samples have a high capability in the generation of heat and can be used as a heating element.

9 November 2021 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
MKMeisam Kheradpisheh
Meisam Kheradpisheh
Mehdi HojjatiMehdi Hojjati
Mehdi Hojjati
This paper aims to study the wrinkle formation of a prepreg with initial defect during steering in automated fiber placement (AFP). Wrinkle formation has a detrimental effect on the mechanical properties of the final product, limiting the AFP applications. A theoretical model for wrinkle formation has been developed in which a Pasternak foundation and a Koiter imperfection model are adapted to model viscoelastic characteristics of the prepreg tack and initial defect of the prepreg, respectively. The initial defect is defined as a slight deviation of the tow’s mid-plane from a horizontal shape. The initial defect is generated in the tow by moving the tow through the guidance system, pressure of the roller, and resin tackiness. Galerkin method, along with the finite difference method (FDM), are employed to solve the wrinkle problem equation. The proposed method is able to satisfy the different boundary conditions for the wrinkle problem completely. The numerical results show that increasing the initial defect leads to a decrease in critical load and an increase in critical steering radius. To validate the theoretical model, experimental results are presented and compared with model-predicted results. It is shown that the model is well able to capture the trends and values of wrinkle formation wavelengths obtained from the experiment.

Verified
Journal Article
Open access
PDF file
MDMina Derakhshani Dastjerdi
Mina Derakhshani Dastjerdi
MCMassimo Carboni
Massimo Carboni
Mehdi HojjatiMehdi Hojjati
Mehdi Hojjati
This paper presents an experimental analysis of the tensile behavior of unidirectional carbon/epoxy prepreg, focusing on the nonlinearity observed at the beginning of the stress–strain curve. Due to the material’s high viscosity, securely holding specimens during testing was challenging, prompting modifications in the gripping method to ensure reliable data. By using a longer gauge length, the slippage impact on elastic modulus measurement was minimized, resulting in good repeatability among the test samples. Experimental findings highlighted the significant interaction between fiber waviness and the viscous matrix, leading to stiffness reduction. The linear stiffness of the samples closely matched that of the fibers and remained unaffected by temperature variations. However, at higher temperatures, the epoxy matrix’s decreased viscosity caused an upward shift in the stiffness plot within the non-linear region. To support the experimental findings, a micromechanical model of prepreg tow with fiber waviness was proposed. An RVE model of periodically distributed unidirectional waved cylindrical fibers embedded within the matrix was developed to predict effective material stiffness parameters. The simulation outcomes aligned well with the uniaxial tensile test of the prepreg tow, demonstrating the proposed RVE model’s capability to accurately predict elastic properties, considering factors like fiber arrangement, waviness, and temperature.

20 August 2025 in Progress in Additive Manufacturing
Verified
Journal Article
Closed access
PDF file
FMFarshad Malekpour
Farshad Malekpour
Mehdi HojjatiMehdi Hojjati
Mehdi Hojjati

27 June 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
MDMina Derakhshani Dastjerdi
Mina Derakhshani Dastjerdi
MCMassiomo Carboni
Massiomo Carboni
Mehdi HojjatiMehdi Hojjati
Mehdi Hojjati
In this paper, the tensile behavior of unidirectional carbon/epoxy prepreg is experimentally analyzed at varying loads and temperatures, focusing on the considerable nonlinearity at the beginning of the stress-strain curve. The high viscosity of this material presented difficulties in securely holding specimens during tensile testing. As a result, modifications were made to the conventional gripping method to enable the acquisition of reliable test data. Additionally, a longer gauge length was chosen to minimize the impact of slippage on the elastic modulus measurement. To support the experiment, a micromechanical model of a prepreg tow with fiber waviness is proposed. An RVE model of periodically distributed unidirectional waved cylindrical fibers embedded within the matrix is developed to predict the effective material stiffness parameters. Numerical results are presented for different amplitude-to-wavelength ratios which indicate the fiber waviness reduces the tensile modulus of the composite. The simulation results are in good agreement with the uniaxial tensile test of the prepreg tow.