We have successfully prepared porous carbon from water hyacinth plants using several steps, i.e., carbonization, activation, and calcination processes. Water hyacinth porous carbon is an alternative as a carbon material due to the ease and low cost of the manufacturing process, abundant raw materials in nature, and its contribution to solving environmental problems. Utilization of water hyacinth weed plants as raw materials for porous carbon will provide added value to water hyacinth. In this research, porous carbon is used as the host material of sulfur in the electrodes of lithium sulfur batteries. The N2 adsorption desorption characterization showed a porous carbon surface area of around 642 m2/g and a total pore volume of 0.713 cm3/g. The sulfur content of the composite electrode of C/S 1:2.5 (%w/w) was 60.6%. The four-line probe (FLP) testing showed electrical conductivity of porous carbon of around 3.93 × 10−2 S/cm and the electrical conductivity of the composite electrode was around 5.4 × 10−4 S/cm. Furthermore, the composite electrodes were applied as cathodes of lithium sulfur batteries, which have thicknesses around 200 µm and sulfur loading of 3.57 mg/cm2. The highest discharge capacity of the battery was 312 mAh/g and the Coulombic efficiency was around 70%.
In the steam power plant in Indonesia the dry steam from separator directly used to drive the turbin. Meanwhile, brine from the separator with low grade temperature reinjected to the earth. The brine with low grade temperature can be converted indirectly to electrical power by organic Rankine cycle (ORC) methods. In ORC power plant the steam are released from vaporization of organic working fluid by brine. The steam released are used to drive an turbine which in connected to generator to convert the mechanical energy into electric energy. The objective of this research is the simulation ORC power plant with n-pentane as organic working fluid. The result of the simulation for brine temperature around 165°C and the pressure 8.001 bar optained the net electric power around 1173 kW with the cycle thermal efficiency 14.61% and the flow rate of n-pentane around 15.51 kg/s. This result enable to applied in any geothermal source in Indonesia.
Cathode composites with high sulfur content have become a concern to develop because they can improve the performance of lithium-sulfur batteries. The high sulfur content in the composite can be obtained from the carbon matrix, which has a high surface area and high electrical conductivity. Activated carbon made from biomass waste can be used as a carbon matrix due to its high surface area and ease of synthesis. In this study, activated carbon was prepared from water hyacinth (ACWH-600), which was carbonized at a temperature of 600 °C with a ZnCl2 activator. Activated-carbon–sulfur composite (ACWH-600/S) was synthesized by mixing activated carbon and sulfur in a ratio of 1:3. The characterizations performed for ACWH-600 and ACWH-600/S were N2 desorption–adsorption to determine the surface area, SEM to determine surface morphology, XRD to determine graphite structure, thermogravimetric analysis test to determine the sulfur content in the composite, and four-line probe conductivity to measure electrical conductivity at room temperature. The surface area, total pore volume, and pore diameter of ACWH were 642.39 m2 g−1, 0.714 cm3 g−1, and 2.22 nm, respectively, while the surface area, total pore volume, and pore diameter of ACWH-600/S were 29.431 m2 g−1, 0.038 cm3 g−1, and 2.54 nm. The conductivity value of ACWH-600 was 3.93 × 10−2 S/cm, while for ACWH-600/S, the conductivity value was 2.24 × 10−4 S/cm. The decrease in conductivity value after activated carbon added sulfur indicated the success of synthesizing a carbon matrix from water hyacinth with high sulfur content. The high sulfur content of 58 wt%, together with the acceptable conductivity value of composite ACWH-600/S, provide an opportunity to apply these composites as cathodes in lithium-sulfur batteries.
1 August 2018 in Journal of Physics: Conference Series