Jian Chen

Prof. Dr. Jian Chen

State Key Lab Chemical Engineering, Department of Chemical Engineering, Tsinghua University, Beijing 100084, China
orcid

Research Focus & Metrics

Academic Career Length

30Years (1997-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 November 2016 in International Journal of Coal Science & Technology
Verified
Journal Article
Open access
PDF file
BXBoyang Xue
Boyang Xue
YYYanmei Yu
Yanmei Yu
Jian ChenJian Chen
Jian Chen
XLXiaobo Luo
Xiaobo Luo
Meihong WangMeihong Wang
Meihong Wang
This paper presented a comparative study of monoethanolamine (MEA) and diethanolamine (DEA) for post-combustion CO2 capture (PCC) process with different process configurations to study the interaction effect between solvent and process. The steady state process model of the conventional MEA-based PCC process was developed in Pro/II® and was validated with the experimental data. Then ten different process configurations were simulated for both MEA and DEA. Their performances in energy consumption were compared in terms of reboiler duty and total equivalent work. The results show that DEA generally has better thermal performances than MEA for all these ten process configurations. Seven process configurations provide 0.38%–4.61% total energy saving compared with the conventional PCC process for MEA, and other two configurations are not favourable. For DEA, except one configuration, other process configurations have 0.27%–4.50% total energy saving. This work also analyzed the sensitivities of three key parameters (amine concentration, stripper pressure and lean solvent loading) in conventional process and five process modifications to show optimization strategy.

12 June 2017 in Environmental Science & Technology
Verified
Journal Article
Closed access
WLWeiliang Luo
Weiliang Luo
QYQi Yang
Qi Yang
WCWilliam Conway
William Conway
GPGraeme Puxty
Graeme Puxty
PFPaul Feron
Paul Feron
Jian ChenJian Chen
Jian Chen

1 May 2007 in Frontiers of Chemical Engineering in China
Verified
Journal Article
Closed access
PDF file
JZJiqin Zhu
Jiqin Zhu
YYYanmei Yu
Yanmei Yu
Jian ChenJian Chen
Jian Chen
WFWeiyang Fei
Weiyang Fei

3 December 2021 in Processes
Verified
Journal Article
Open access
PDF file
SLSimeng Li
Simeng Li
HLHan Li
Han Li
YYYanmei Yu
Yanmei Yu
Jian ChenJian Chen
Jian Chen
N-(2-Hydroxyethyl) piperazine (HEPZ) has a chemical structure similar to PZ and has less volatility. It is not easy to volatilize in a continuous operation device. It is studied to replace PZ as a promotor to increase the CO2 capture rate. This paper researches the lowest energy consumption and absorbent loss of HEPZ/H2O in the absorption-regeneration process, and compares it with another five amines, including PZ, MEA, 1-MPZ, AMP and DMEA. Based on the thermodynamic model, this work establishes a process simulation based on the equilibrium stage, assuming that all stages of the absorption and desorption towers reach thermodynamic equilibrium and CO2 recovery in the absorption tower is 90%. By optimizing the process parameters, the lowest thermodynamic energy consumption and absorbent loss of process operation are obtained. Our results show that HEPZ as a promotor to replace PZ and MEA has significant economic value. The lowest reboiler energy consumption of HEPZ with the optimal process parameters is 3.018 GJ/tCO2, which is about 35.2% lower than that of PZ and about 11.6% lower than that of MEA, and HEPZ has the lowest solvent loss. The cyclic capacity is 64.7% higher than PZ and 21.6% lower than primary amine MEA.

19 March 2022 in Processes
Verified
Journal Article
Open access
PDF file
YYYi Ye
Yi Ye
XZXinglei Zhao
Xinglei Zhao
Jian ChenJian Chen
Jian Chen
Mengxiang FangMengxiang Fang
Mengxiang Fang
Chemical absorbents with low-energy requirements have become the primary focus of the research on CO2 capture from flue gas in power plants. To verify the absorption performance of the NICE absorbent developed by the National Institute of Clean-and-Low-Carbon Energy in China, a performance optimization test was conducted in Zhejiang University’s pilot-scale platform, and the effects of the liquid–gas ratio, regeneration pressure, rich liquid fractional flow, and interstage cooling on the absorption performance and regeneration energy consumption were investigated. The results showed that in the CO2 pilot test, the optimized minimum regeneration energy consumption was 2.85 GJ/t CO2, and the corresponding process parameters were as follows: a liquid–gas ratio of 1.82 L/m3, regeneration pressure of 191 kPa, an interstage cooling temperature of 40 °C, and a rich liquid fractional flow ratio of 0.18. This study preliminarily verified the low-energy consumption performance of the NICE absorbent and showed its good potential for industrial applications. Additionally, the NICE absorbent showed promise for capital and operating cost savings because of its low liquid–gas ratio.

31 May 2008 in Journal of Macromolecular Science, Part A
Verified
Journal Article
Closed access
HYHong Ye
Hong Ye
JLJiding Li
Jiding Li
YLYangzheng Lin
Yangzheng Lin
Jian ChenJian Chen
Jian Chen
CCCuixian Chen
Cuixian Chen
Pervaporation is promising in the separation of benzene/cyclohexane mixture for the petrochemical industry. Two kinds of pervaporation membrane materials, including PEA‐based polyurethaneurea (PUU) and polyurethaneimide (PUI), were successfully synthesized from the same soft segment of poly(ethylene adipate)diol (PEA) and different hard segments via a two‐step method. The hard segment of PUU was prepared from toluene diisocyanate (TDI) and 4,4′‐diaminodiphenyl methane (MDA), while that of PUI was from 4,4′‐methylene‐bis(phenylisocyanate) (MDI) and pyromellitic dianhydride (PMDA). The structures and properties of PUU and PUI were characterized by means of FT‐IR, DSC and TGA. During the pervaporation experiment, the PUI membranes had a flux of 12.13 kg µm m−2 h−1 and separation factor of 8.25, while the PUU membranes had a flux of 26.35 kg µm m−2 h−1 and separation factor of 6.29 for 50 wt% benzene in the benzene/cyclohexane mixture at 40°C. The effects of the structures of hard segments on pervaporation performances were discussed. The investigation of the relationship in molecular structure and PV performances will be helpful for the choice and design of membrane materials in the separation of benzene/cyclohexane mixture.