Sea breeze (SB) phenomena may strongly influence air quality and lead to important effects on human health. In order to study the impact of SB dynamics on the properties and toxicity of aerosols, an atmospheric mobile unit was deployed during a field campaign performed in an urbanized and industrialized coastal area in Northern France. This unit combines aerosol samplers, two scanning lidars (Doppler and elastic) and an air-liquid interface (ALI, Vitrocell®) in vitro cell exposure device. Our study highlights that after the passage of an SB front, the top of the atmospheric boundary layer collapses as the thermal internal boundary layer (TIBL) develops, which leads to high aerosol extinction coefficient values (>0.4 km−1) and an increase of PM2.5 and NOx concentrations in the SB current. The number-size distribution of particles indicates a high proportion of fine particles (with diameter below 500 nm), while the volume-size distribution shows a major mode of coarse particles centered on 2–3 µm. Individual particle analyses performed by cryo-transmission scanning electron microscopy (cryo-TSEM)-EDX highlights that submicronic particles contained a high fraction of secondary compounds, which may result from nucleation and/or condensation of condensable species (vapors or gaseous species after photo-oxidation). Secondary aerosol (SA) formation can be enhanced in some areas, by the interaction between the SB flow and the upper continental air mass, particularly due to the effect of both turbulence and temperature/humidity gradients between these two contrasting air masses. Potential areas of SA formation are located near the ground, during the SB front passage and in the vicinity of the SB current top. During the sea breeze event, an increase in the oxidative stress and inflammation processes in exposed lung cells, compared to the unexposed cells, can also be seen. In some instances, short singularity periods are observed during SB, corresponding to a double flow structure. It consists of two adjacent SB currents that induce an important increase of the TIBL top, improving the pollutants dispersion. This is associated with a substantial decrease of aerosol mass concentrations.
The atmospheric boundary layer (ABL) height plays a key role in many atmospheric processes as one of the dominant flow length scales. However, a systematic quantification of the ABL height over the entire range of scales (i.e., with periods ranging from one minute to one year) is still lacking in literature. In this work, the ABL height is quantified based on high-resolution measurements collected by a scanning pulsed Doppler LiDAR during the recent American WAKE experimeNt (AWAKEN) campaign. The high availability of ABL height estimates (≈2200 collected over one year and each of them based on 10-min averaged statistics) allows to robustly assess five different ABL height models, i.e., one for convective thermal conditions and four for stable conditions. Thermal condition is quantified by a stability parameter spanning three orders of magnitude and probed by near-ground 3D sonic anemometry. The free-atmosphere stability, quantified by the Brunt–Väisälä frequency, is both calculated from simultaneous radiosonde measurements and obtained from the best fit of two of the chosen ABL height models. Good agreement is found between the data and three of the chosen models, quantified by mean absolute errors on the ABL height between 281 and 585 m. Furthermore, the seasonal variability of the convective ABL height model parameters (−15% to +23% with respect to the year baseline) agrees with the variability of buoyancy-generated turbulence caused by the variation in solar radiation throughout the year.
1 November 2017 in Journal of Waterway, Port, Coastal, and Ocean Engineering
The results of an experimental study on combined wave and current flow around a partially submerged cylinder with a large Reynolds number ( = 5.96 × 104) are reported. The measured instantaneous velocity time-series data were analyzed to acquire insight into the first-, second-, third-, and fourth-order statistical moments. It was observed that turbulence generated because of the surface wave plays a significant role in the occurrence of vortex lock-on, which in turn alters the excitation frequency. For the vortex lock-on case in which the shedding frequency is the same as the natural shedding frequency, the recirculation zone is significantly reduced. However, for higher wave frequencies, the shedding frequency was modulated and the recirculation was somewhat enlarged. The comparative study between only current flow (OCF) and combined wave-current flow (WCF) showed that the intermittency in turbulence was larger for the OCF case (without a cylinder) than for the WCF case. The surface-wave-generated vortices induced around the cylinder interacted with the vorticity shear layers at the side of the cylinder and at the wake region, resulting in the formation of new induced wake vortices. These induced wake vortices controlled the recirculation region behind the cylinder.
Reynolds stress anisotropy is estimated from the stress spheroids, based on 20 Hz ultrasonic anemometer measurements, performed in the coastal area of northern France, over a 1.5-year long period. Size and shape variation (i.e., prolate, oblate, disk, rod, etc.) of stress spheroids are used for the characterization of energy redistribution by turbulent eddies. The sea-breeze (SB) events were identified using a change in wind direction from seaward (SWD) to landward (LWD) during the day time. We found that the LWD wind creates more turbulent anisotropic states than SWD wind. The prolate-shaped stress spheroids correspond to small-scale turbulence observed during LWD wind, while oblate spheroids are found during SWD winds. Moreover, it was found that during LWD winds, large turbulence kinetic energy (TKE) in the flow field produces large stress spheroids. On the contrary, during SWD winds, a smaller level of TKE is responsible for small-size stress spheroid formation. The average volume of the corresponding Reynolds stress spheroids during the LWD is 13% larger than that of during SWD wind.
Wind energy is widely used in renewable energy systems but the randomness and the intermittence of the wind make its accurate prediction difficult. This study develops an advanced and reliable model for multi-step wind variability prediction using long short-term memory (LSTM) network based on deep learning neural network (DLNN). A 20 Hz Ultrasonic anemometer was positioned in northern France (LOG site) to measure the random wind variability for the duration of thirty-four days. Real-time turbulence kinetic energy is computed from the measured wind velocity components, and multi-resolution features of wind velocity and turbulent kinetic energy are used as input for the prediction model. These multi-resolution features of wind variability are extracted using one-dimensional discrete wavelet transformation. The proposed DLNN is framed to implement multi-step prediction ranging from 10 min to 48 h. For velocity prediction, the root mean square error, mean absolute error and mean absolute percentage error are 0.047 m/s, 0.19 m/s, and 11.3% respectively. These error values indicate a good reliability of the proposed DLNN for predicting wind variability. We found that the present model performs well for mid-long-term (6-24h) wind velocity prediction. The model is also good for the long-term (24-48h) turbulence kinetic energy prediction.