Ayyanna Habal

Dr. Ayyanna Habal

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2017 in Journal of Materials in Civil Engineering
Verified
Journal Article
Closed access
DSDharamveer Singh
Dharamveer Singh
PAPrabin Kumar Ashish
Prabin Kumar Ashish
AKAniket Kataware
Aniket Kataware
AHAyyanna Habal
Ayyanna Habal
Modification of asphalt binder with Elvaloy (Elv) and polyphosphoric acid (PPA) has been reported to have better performance. However, such modification may increase mixing and compaction temperatures of asphalt binder. Furthermore, the positive effect of PPA may get neutralized with the addition of lime, which can lead to inferior performance of asphalt binders. Recently, different types of warm mix additives (WMA) are being introduced to reduce production and construction temperatures of asphalt binder. However, the effects of WMA additives with and without lime on various rheological response of PPA + Elv modified asphalt binder is not well understood so far. Therefore, the present study was undertaken to evaluate the rutting and fatigue performance of PPA + Elv modified asphalt binder (referred as Control binder) containing three WMA additives (water, chemical, and wax-based) with and without lime. The multiple stress creep recovery (MSCR) and linear amplitude sweep (LAS) tests were conducted to capture the rutting and fatigue performance of asphalt binders, respectively. The results show that rutting and fatigue performance of Control asphalt binder decreased with the addition of chemical and water-based WMA additives. The performance of Control asphalt binder further deteriorated when these WMA additives (chemical and water) were used with lime. Interestingly, the addition of wax showed higher rutting resistance and similar fatigue life as that of Control asphalt binder. The addition of lime with wax additive showed improved rutting resistance and reduced fatigue life compared with Control asphalt binder. Regardless of the type of WMA additives, the addition of lime decreased the fatigue life of Control asphalt binder. The adverse effect of lime was prominent when used with wax compared with water and chemical-based WMA additives. Furthermore, the addition of WMA additives increased the stress sensitivity of Control asphalt binder. The stress sensitivity of asphalt binder further increased when wax and chemical-based WMA additives were used with lime. However, use of water-based WMA additive and lime reduced the stress sensitivity of Control asphalt binder. Overall, it can be concluded that the performance of Elv + PPA modified asphalt binder depends largely on the type of WMA additives and their combination with lime.

17 June 2019 in International Journal of Pavement Engineering
Verified
Journal Article
Closed access
AHAyyanna Habal
Ayyanna Habal
DSDharamveer Singh
Dharamveer Singh
The present study was undertaken to evaluate the effects of different warm mix asphalt (WMA) additives on bonding behaviour of asphalt binder and aggregates using two different approaches: (i) The surface free energy (SFE) method and (ii) The asphalt bond strength (ABS) test. The study involved two phases, the first phase involved measurement of the SFE of control, and WMA (Sasobit, Advera, and Rediset) modified asphalt binders by the Wilhelmy plate method, and aggregate's (limestone and granite) SFE by the dynamic vapour sorption (DVS) method. Thereafter, bond energies were computed using SFE method for understanding the bonding behaviour of WMA modified binders with different aggregates in dry and wet conditions. The second phase involved direct measurement of bond strength and failure pattern between asphalt binder and aggregate combinations by the ABS test in both dry and wet conditions. Furthermore, bond strength of all combination of asphalt binder and aggregates were compared by SFE and ABS methods. The results indicated that Sasobit and Advera effectively contributed in enhancing the cohesive energy of control binder, whereas Rediset decreased the cohesive energy of control binder. Bond strength of WMA modified binder depends on both aggregate type and WMA additives. The results show that asphalt binder with Sasobit can have better bonding performance with limestone (basic) aggregate, whereas, asphalt binder after addition of Advera showed better bonding performance with granite (acidic) aggregate. After wet conditioning, asphalt binders with limestone (basic) aggregate combinations exhibited cohesive failure showing minimal effect of water on bond strength compared to binders with granite (acidic) aggregate combinations which showed adhesive failure. The comparison of bond strength by mechanical ABS test and energy based SFE methods have shown a fair correlation between bond strength ratio (BSR) and energy ratio (ER).

1 June 2016 in Construction and Building Materials
Verified
Journal Article
Closed access
AHAyyanna Habal
Ayyanna Habal
DSDharamveer Singh
Dharamveer Singh

1 July 2018 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Closed access
AHAyyanna Habal
Ayyanna Habal
DSDharamveer Singh
Dharamveer Singh
The bond between aggregate and asphalt binder depends on many factors, such as chemistry of materials, nature of aggregates, and quality of asphalt binder. The present study evaluates the effects of recycled asphalt pavement (RAP) on the bonding behavior of asphalt binder for acidic (granite and quartzite) and basic (basalt and limestone) aggregates. AC30 binder was blended with different proportions of RAP binder (15%, 25%, and 40%). The interfacial energy and bond strength of 16 combinations (four asphalt binders × four aggregates) of aggregate-asphalt binder system were evaluated based on a surface free energy (SFE) approach and binder bond strength (BBS) test, respectively. One of the strong motivations of the present study was to evaluate how interfacial energy parameters calculated based on the SFE of an aggregate-asphalt binder system may correlate with the outcome obtained from a BBS test. The results showed that AC30 binder modified with RAP binder had a good performance for basic aggregates compared with acidic aggregates. Basic aggregates (limestone and basalt) showed cohesive failure before and after conditioning, indicating minimal effects of water on interfacial bond strength. However, acidic aggregates (granite and quartzite) showed cohesive failure in dry conditions and adhesive failure after wet conditioning, implying detrimental effects of water on interfacial bond strength for these aggregates. The failure pattern of aggregates in cohesion was supported by a reduction in cohesion energy of asphalt binder after the addition of RAP binder. Correlation between interfacial energy parameters (obtained from SFE) and BBS strength depends on aggregate types and failure patterns.

1 June 2017 in Journal of Performance of Constructed Facilities
Verified
Journal Article
Closed access
AHAyyanna Habal
Ayyanna Habal
DSDharamveer Singh
Dharamveer Singh
The present study was undertaken to understand the moisture damage resistance of unmodified and ground tire rubber (GTR)–modified asphalt binders containing three different type of warm mix asphalt (WMA) additives using the surface free energy (SFE) approach. The SFE parameters of unmodified and GTR-modified asphalt binders with and without WMA additives were determined in the laboratory using the Wilhelmy plate method. The SFE of two types of aggregate, namely, granite and limestone, were adopted from literature. Thereafter, work of adhesion, work of cohesion, work of debonding, and energy ratio (ER) were estimated for a total of 16 different combinations of aggregate and asphalt binder. An attempt was made to evaluate sensitivity of SFE parameters with elemental composition (carbon, hydrogen, nitrogen, and sulfur) of asphalt binder. The results showed that moisture damage resistance of unmodified and GTR-modified asphalt binder decreases with addition of WMA additives. The control asphalt binder with Rediset (Akzo Nobel, Netherlands) showed better bond with aggregate, followed by Sasobit (SasolWax, Hamburg, Germany) and Advera (PQ Corporation, Malvern, Pennsylvania). The limestone aggregate showed better moisture damage resistance compared with granite aggregate. The elemental composition (CHNS) of an asphalt binder found to have a fair correlation with SFE parameters.

1 January 2018 in Construction and Building Materials
Verified
Journal Article
Closed access
DSDharamveer Singh
Dharamveer Singh
AHAyyanna Habal
Ayyanna Habal
PAPrabin Kumar Ashish
Prabin Kumar Ashish
AKAniket Kataware
Aniket Kataware