Thick SU-8 photoresist has been a popular photoresist material to fabricate various mechanical, biological, and chemical devices for many years. The accuracy and precision of the ultraviolet (UV) lithography process of thick SU-8 depend on key parameters in the set-up, the material properties of the SU-8 resist, and the thickness of the resist structure. As feature sizes get smaller and pattern complexity increases, accurate control and efficient optimization of the lithography process are significantly expected. Numerical simulations can be employed to improve understanding and process design of the SU-8 lithography, thereby allowing rapid related product and process development. A typical comprehensive lithography of UV lithography of thick SU-8 includes aerial image simulation, exposure simulation, post-exposure bake (PEB) simulation, and development simulation, and this article presents an overview of the essential aspects in the comprehensive simulation. At first, models for the lithography process of the SU-8 are discussed. Then, main algorithms for etching surface evolvement, including the string, ray tracing, cellular automaton, and fast marching algorithms, are introduced and compared with each other in terms of performance. After that, some simulation results of the UV lithography process of the SU-8 are presented, demonstrating the promising potential and efficiency of the simulation technology. Finally, a prospect is discussed for some open questions in three-dimensional (3D) comprehensive simulation of the UV lithography of the SU-8.
Based on the first resonance frequency measurement of multilayer beams, a simple extraction method has been developed to extract the Young’s modulus of individual layers. To verify this method, the double-layer cantilever, as a typical example, is analyzed to simplify the situation and finite element modeling (FEM) is used in consideration of the buckling and unbuckling situation of cantilevers. The first resonance frequencies, which are obtained by ANSYS (15.0, ANSYS Inc., Pittsburgh, PA, USA) with a group of thirteen setting values of Young’s modulus in the polysilicon layer are brought into the theoretical formulas to obtain a new group of Young’s modulus in the polysilicon layer. The reliability and feasibility of the theoretical method are confirmed, according to the slight differences between the setting values and the results of the theoretical model. In the experiment, a series of polysilicon-metal double-layer cantilevers were fabricated. Digital holographic microscopy (DHM) (Lyncée Tech, Lausanne, Switzerland) is used to distinguish the buckled from the unbuckled. A scanning laser Doppler vibrometer (LDV) (Polytech GmbH, Berlin, Germany) system is used to measure the first resonance frequencies of them. After applying the measurement results into the theoretical modulus, the average values of Young’s modulus in the polysilicon and gold layers are 151.78 GPa and 75.72 GPa, respectively. The extracted parameters are all within the rational ranges, compared with the available results.
14 January 2021 in IEEE Transactions on Industrial Electronics
In this article, the benchmark drift of micromachined thermal wind sensor due to the packaging asymmetry has been analyzed and compensated. For the ideal wind sensors with symmetric packaging, the benchmark does not vary with speed and direction. However, for the real sensors, especially for handmade ones, packaging asymmetry problems are usually inevitable. Consequently, benchmark drifts with wind because of different thermal distribution in each direction, which was verified by the proposed lumped parameters model. The real sensors were tested in a wind tunnel and results showed the benchmark drift as well. The contribution of this work lies in the establishment of the equation of benchmark dependent on wind speed, which can predict benchmark value under different wind speeds by calibration at zero wind speed. This compensation method is extremely simple and convenient for industrial production. After compensation, the relative wind speed errors are reduced from 46 to 8% up to 30 m/s, and the wind direction errors are reduced from 30° to 7° over the full range of 360°.
5 October 2020 in Journal of Micromechanics and Microengineering
In this paper, we propose a thermal wind speed sensor Verilog-A model with thermal-fluid-electric hybrid characteristics. Because the structure of the thermal wind sensor and the interface circuit chip are designed separately, which cannot effectively carry out MEMS-IC (integrated circuit) co-simulation, the overall performance of the sensor and interface circuit chip is prone to large deviation. At the same time, the separation of MEMS structure and IC design process leads to long product development cycle and high cost. This paper proposes an improved simulation model by analyzing the behavior characteristics of the thermal wind speed sensor. The simulation model consists of 11 thermistors, 3 capacitors, a voltage-controlled voltage source, and a voltage-controlled current source. The Taylor series expansion of the differential equation of heat conduction is carried out, and then the thermistor and capacitor networks are established according to the corresponding relationship between the thermal parameters and the electrical parameters, including the thermal conduction unit, the convection unit and the heat capacity in the chip. The model fully considers the effects of various physical effects and parasitic effects, and is implemented using the hardware description language Verilog-A. The sensor and interface circuit can be simulated simultaneously to optimize the circuit design. It is beneficial to the integration of sensors and interface circuit, reducing the number of tape-outs, increasing the success rate, and reducing costs. The consistency between the simulation results and the experimental curves verified the correctness of the macro model. The behavior characteristics of constant power (CP) and constant temperature heating were described. In CP mode, the output voltage error is less than ± 6.5%, the chip temperature error is less than 4.0%. The presented modeling approach can be the basis for the development of complete MEMS-IC design technology library of thermal wind speed sensor, aiming at optimum designs of integrated thermal wind speed sensor.
This work presents a novel strategy for efficiently extracting macro models from multiphysics microelectromechanical systems (MEMS) devices with weak-coupling. To validate the strategy, the packaged thermal wind sensor is chosen to verify the feasibility of the strategy for the first time. Based on the characteristics of the packaged thermal wind sensor, it can be divided into three distinct energy fields: thermal field, fluid field, and electric field. The packaged thermal wind sensor is initially built as the finite element model which represents a pure thermal system under no wind flow conditions. And then the thermal system with Linear and Time Invariant (LTI) is identified as a state space model by its step response obtained by transient simulation of the finite element model. Other energy fields can be regarded as negative inputs for the state space model. Subsequently, based on the relationship of independent energy fields, coupling the thermal field, fluid field and electric field by Verilog-A to extract macro model of sensor. Remarkably, the macro model based on this strategy takes into account geometric factors and material parameters. The tests show that the error of far group thermistors between system-level simulation and experiment is less than 5% under the conventional wind speed range on constant power (CP) mode, and the results of wind direction between them also show a significant degree of overlap. In brief, the strategy of extracting macro model enables the direct construction of connections between finite element model of MEMS devices and Integrated Circuits.