Mervat Ibrahim

Prof. Dr. Mervat Ibrahim


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 December 2016 in Metallurgical and Materials Transactions B
Verified
Journal Article
Closed access
PDF file
MIMervat Ibrahim
Mervat Ibrahim
ANAdel Nofal
Adel Nofal
MMM. M. Mourad
M. M. Mourad

2 June 2020 in International Journal of Metalcasting
Verified
Journal Article
Closed access
PDF file
MIMervat Ibrahim
Mervat Ibrahim
SEShimaa El-Hadad
Shimaa El-Hadad
MMMohamed Mourad
Mohamed Mourad

29 September 2016 in International Journal of Cast Metals Research
Verified
Journal Article
Closed access
MIMervat Ibrahim
Mervat Ibrahim
MMMohamed Mahmoud Mourad
Mohamed Mahmoud Mourad
ANAdel Abdelmonem Nofal
Adel Abdelmonem Nofal
AFAhmed I. Z. Farahat
Ahmed I. Z. Farahat
Ductile cast iron was developed by adding Aluminium (up to16 wt%Al). Effects of aluminium on microstructure, hardness, oxidation resistance at high temperature and damping capacity of cast iron were studied. Adding Al up to 4.0 wt% raised degree of graphitisation. More than 4.0 wt% up to 13.8 wt%Al showed precipitation of hard carbides. Hardness was increased significantly by increasing Al due to formation of intermetallic compounds. More than 5.8 wt%Al showed a higher oxidation resistance due to formation of complex Fe-Al oxide, acted as a protective and adherent scale. Damping capacity of 2.6 and 4.0 wt%Al was increased as the volume fraction of graphite increased as well as the change of graphite from spheroidal to compacted ones. Damping capacity of 16 wt%Al was enhanced due to high ferrite (86%) containing graphite. However, decreasing of ferrite and disappearing of graphite as well as presence of carbides highly deteriorated damping capacity of 5.8, 9, 12.8 and 13.8 wt%Al cast iron.

1 January 2020 in Materials Research Express
Verified
Journal Article
Open access
PDF file
KAK A Abdelghafar
K A Abdelghafar
MIMervat Ibrahim
Mervat Ibrahim
MSMadiha A Shoeib
Madiha A Shoeib
MWM A Waly
M A Waly
Cu45Mn25Al15Fe5Cr5Ni5 high entropy alloy was prepared using casting route. Detailed microstructural analysis revealed the formation of dendritic structure in the as-cast sample. The results showed that the dendrite (DR) regions are riched with Cu and Mn, while the inter-dendrite (ID) regions are riched with Cr and Fe. Metallographic investigation was conducted using optical microscope and scanning electron microscope as well. Determination of phase analysis was carried out using x-ray diffraction. Corrosion properties were studied via Auto LAB PGSTAT 302N, supplied with Nova software. The investigated alloy demonstrates superior corrosion resistance with average corrosion rate 0.056 mm year−1.

23 January 2019 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
SEShimaa El-Hadad
Shimaa El-Hadad
MIMervat Ibrahim
Mervat Ibrahim
MMMohamed Mourad
Mohamed Mourad
High-entropy alloys (HEAs) are multiprincipal element alloys with controllable properties. Studying the mechanical properties of these alloys and relating them to their microstructures is of interest. In the current investigation, Fe31Mn28 Ni15Al24.5Tix high-entropy alloys with Ti content (0–3 wt.%) were prepared by casting in an induction furnace. Different heat treatments were applied, and the microstructure and hardness of the cast samples were studied. It was observed that addition of up to 3.0 wt.% Ti significantly increases the hardness of the alloy from 300 to 500 (Hv) by the combined effect of solid solution strengthening and via decreasing lamellar spacing. Heat treatment at 900°C for 10 h enhanced the hardness at lower Ti percentages (0.0–0.8 wt.%) by decreasing the lamellar spacing, while no change was observed at higher Ti content. It was also observed that extending the treatment time to 20 h affected negatively the hardness of the alloy. Concluding, HEAs can achieve high hardness using low-cost principle elements with minor alloying additives compared to the other traditional alloys.

9 May 2025 in Processes
Verified
Journal Article
Open access
PDF file
Mohammed AtieaMohammed Atiea
Mohammed Atiea
RRReham Reda
Reham Reda
Sabbah AtayaSabbah Ataya
Sabbah Ataya
MIMervat Ibrahim
Mervat Ibrahim
High-performance copper alloys are crucial for integrated circuit lead frames due to their high density, multifunctionality, and low cost. High-performance copper alloys typically address the competing issues of high strength and high electrical conductivity through alloying and processing control methods. However, the traditional methods for developing these alloys are time-consuming, expensive, and complex processes. This study utilizes Explainable AI by employing machine learning (ML) and deep learning (DL) techniques to predict the hardness (HRC) and electrical conductivity (mS/m) based on the alloy composition, including Cr, Zr, Ce, and La, and the processing parameters, namely the aging time, of Cu-Cr-Zr alloys. A comprehensive dataset of 47 experimental Cu-Cr-Zr alloy samples, derived from prior experimental studies, was analyzed using feature engineering, correlation analysis, and explainability methods such as SHapley Additive exPlanations (SHAP). Various ML models, including ensemble methods like XGBoost, CatBoost, and AdaBoost, were evaluated for their predictive performance. The feature importance analysis revealed that the aging time and Zr content significantly influence the hardness, followed by Ce content, while Cr and La contents reveal a weak contribution to hardness values. Electrical conductivity is predominantly controlled by aging time, with a weak negative influence of the alloying elements. These findings align well with metallurgical principles, where microstructural refinement and precipitation behavior dictate the hardness and conductivity of Cu-Cr-Zr alloys. Hyperparameter tuning and model stacking further enhanced the predictive accuracy, with the final stacked models achieving R2 scores of 0.8762 for hardness within a training time of 1.739 s and 0.8132 for electrical conductivity within a training time of 1.091 s. These findings demonstrate the effectiveness of ML-driven approaches in material property predictions, providing valuable insights for material design and property processing parameter optimization.