The foundry industry generates large amounts of spent foundry sands, which are stored, available for recovery in other industrial sectors but unfortunately poorly exploited. Different authors have studied the possibility of recovering them in concretes, which would also allow production of more sustainable cementitious materials. The variability of their results highlights the importance of a better understanding of the potential influential parameters of the by-products. Unfortunately, exhaustive characterizations of the materials are rarely performed, especially for chemically bound foundry sands. This article presents a case study for the recovery of a spent chemical foundry sand with an exhaustive physicochemical characterization of the by-product and an analysis of its influence on the workability and mechanical strengths of cementitious materials. The tests recommended by the European standard for aggregates for concrete confirmed the suitability of the by-product. Associated with additional chemical tests (scanning electron microscopy, X-ray fluorescence, X-ray diffraction, etc.) as well as metallic particles characterization, they highlighted possible influential parameters. The workability and mechanical resistance tests carried out on mortars and concretes confirmed the influence of the fineness of the by-product associated with other parameters. Its use at a substitution rate of 30% results in a strength class C 30/37 concrete.
The purpose of this experimental paper is to examine the adhesion properties between non-woven plastic sheets and cement mortar. Specifically, the effect of w/c ratio and quantity of superplasticizer on the peeling force required for the detachment of tissue from the surface of prisms was studied in detail. Therefore, two types of mortar mixtures were prepared: (1) mixtures without superplasticizer with three different w/c ratios of 0.45, 0.50, and 0.55, and (2) mixtures with reduced amounts of water and three various percentages of superplasticizer of 0.0%, 1.11%, and 2.17% (by weight of cement). For this purpose, bond tests with a special setup, interferometry and microscopic analyses, and mechanical tests were performed. The results highlight that non-woven sheets had strong adhesion to cement mortar without using any adhesive materials. However, the peeling force improved by 15.78% as the w/c ratio increased from 0.50 to 0.55. Conversely, this force declined by 24.50% as the w/c ratio decreased from 0.50 to 0.45. In addition, the peeling force decreased by 20.62% as the w/c ratio decreased from 0.50 to 0.45 and 1.11% superplasticizer was added to the mixtures. This property decreased further by 38.29% as the w/c ratio lowered to 0.40, and the amount of superplasticizer increased to 2.17%. The interferometry and microscopic analyses clearly demonstrate that the adhesion between tissue and mortar is largely related to the surface texture, amount of cement paste, and quantity of residual fibers on the surfaces of samples. It indicates that mortar samples with higher w/c ratios had a smoother surface, and providing more contact area for microfilaments, which resulted in thicker layers of remaining fibers compared to the specimens with a lower w/c ratio. Even though there was not much difference in the surface texture of specimens with superplasticizer and lower w/c ratios, because of their similar workability. Still, thicker layers of microfilaments remained on the surface of specimens containing a lower amount of superplasticizer, which resulted in strong adhesion between sheet and cement mortar.
Ce travail porte sur la valorisation des laitiers d'aciérie de conversion (slag BOF) dans les liants hydrauliques routiers. L'étude comprend un aspect fondamental dédié à la caractérisation des slag BOF, à l'analyse de leur comportement hydraulique et à l'étude de leur activation thermique et/ou chimique. Ils contiennent majoritairement 2S, C2F, Fe1-xO et CaO. Ils atteignent en pâte pure des résistances à la compression de 50 MPa à 180 jours. La finesse de mouture, la température et CaCl2 améliorent les résistances aux jeunes âges. L'étude comprend un aspect appliqué, consacré à la confection de liants hydrauliques routiers à base de slag BOF. Les propriétés mécaniques ont été étudiées selon la normalisation. Les résultats montrent que l'utilisation de 30 à 40% de slag BOF permet d'obtenir des liants hydrauliques routiers ayant des performances conformes à l'usage. Ce résultat constitue une solution intéressante pour valoriser ces coproduits industriels.