Hidrojenin elektroliz yöntemi ile yüksek saflıkta elde edilebileceği kaynaklar arasında olan kömür, düşük maliyeti ve büyük arz nedeniyle cazip bir seçenektir. Bu çalışmada, Çanakkale/Çan linyiti-su bulamaçlarının elektrolizi ile hidrojen üretimine etki eden çeşitli parametreler (kömür partikül büyüklüğü, sıcaklık, karıştırma hızı, elektrot malzemesi ve Fe+2 iyonunun etkisi) incelenmiştir. Deneyler, iki elektrotlu (anot/katot) elektroliz hücresinde, elektrolit olarak 1 M H2SO4 kullanılarak asidik ortamda ve atmosferik basınçta gerçekleştirilmiştir. Atmosferik basınçta gerçekleştirilen deneylerde elektrot olarak bakır-bakır ve çinko-çinko elektrot kullanılmıştır. Sıcaklığın akım yoğunluğu üzerindeki etkisini belirleyebilmek için, oda sıcaklığından 80oC'ye kadar düzenli aralıklarla ölçümler yapılmıştır. Akım yoğunluğunun sıcaklıkla arttığı tespit edilmiştir. Ayrıca, üç farklı partikül boyutunda (1-0,5 mm, 0,5-0,25 mm ve <0,25 mm) yapılan deneylerde, en yüksek akım yoğunluğu değerleri en küçük partikül boyutunda elde edilmiştir. Fe+2 iyonunun etkisi, kömür-su karışımına 0,1 M FeSO4 ilave edilerek sağlanmıştır ve Fe+2 iyonu ilavesinin, akım yoğunluğunu 80°C ve 0,73 V'da yaklaşık %60 artırdığı görülmüştür. Karıştırma hızının iki katına çıkarılması ile de akım yoğunluğu 80°C ve 0,73 V’da %16 artmıştır.
As an alternative to hydrogen production by electrolysis of water, using as raw material waste valorization and organic pollutants in wastewater are crucial issues. In this context, electrolysis of black water, produced as waste in olive oil production and high energy source potential due to the aromatic compounds in its content, was carried out in this study. Parametric studies were carried out by examining the effect of working conditions on hydrogen production. The experiments using a two-chamber electrolysis cell examined the effects of catalytic additive (Fe2+/3+), temperature (26oC-60oC-70oC-80oC), type of electrode (Cu/Cu, Zn/Zn and Pd/Pt) and electrolyte (H2SO4, H3PO4, HCl, C2H2O4 and C2H4O2), membrane and pretreatment applied to the membrane. In the electrolysis of black water with FeSO4 and acidic electrolyte (H2SO4) using a pretreated Nafion XL membrane on the Zn/Zn electrode pair, pure H2 formation at the cathode was determined. Under these conditions, 1.9 mA/cm2 current density was obtained at 1 V potential and room temperature.
This study investigates the electrolysis of formic acid for hydrogen production, focusing on the effects of various parameters and materials. In the first phase, experiments were conducted using a single-compartment electrolysis cell with Pd/Pt electrodes at 20°C. The effect of formic acid concentration, electrolytes, and electrode materials on current density was analyzed. The highest current density (5.18 mA/cm² at 1 V) was achieved with H₂SO₄ as an electrolyte. The Zn/Zn electrode pair significantly outperformed Pd/Pt, yielding four times higher current density. In the second phase, electrolysis conditions for hydrogen production at low voltage (2 V) and temperature (50°C) were optimized. Pure hydrogen was obtained at the cathode, confirming the successful hydrogen production under these conditions. Faradic efficiency reached 92% at 2 V, with a high hydrogen production rate. The use of cost-effective Zn electrode, along with mild electrolysis conditions, enhances the practicality and sustainability of the process. These findings highlight that formic acid electrolysis is a promising and efficient method for pure hydrogen production, offering an economical and sustainable alternative for hydrogen generation.