A scheme that combines optoelectronic tweezers (OET) with spectroscopic analysis is presented. Referred to as spectral tweezers, the approach uses a single focused light beam that acts both as the trapping beam for OET and the probe beam for spectroscopy. Having simultaneous manipulation and spectral characterization ability, the method is used to isolate single micro-samples from clusters and perform spectral measurements. Experimental results show that a characteristic spectral signature can be obtained for a given sample. The proposed approach can be easily integrated into the optical setups used for conventional OETs with only a few additional optical components, making it a convenient tool for bio-analytical applications.

We present a device that can achieve controlled transport of colloidal microparticles using an array of micro-electrodes. By exciting the micro-electrodes in regular sequence with an AC voltage, a time-varying moving dielectrophoretic force-field is created. This force propels colloidal microparticles along the electrode array. Using this method, we demonstrate bidirectional transport of polystyrene micro-spheres. Electromagnetic simulation of the device is performed, and the dielectrophoretic force profile around the electrode array is mapped. We develop a Brownian dynamics model of the trajectory of a particle under the influence of the time-varying force-field. Numerical and experimental results showing controlled particle transport are presented. The numerical model is found to be in good agreement with experimental data. The developed numerical framework can be useful in designing and modeling lab-on-a-chip devices that employ external non-contact forces for micro-/nanoparticle manipulation.

An impedance analysis for optically induced dielectrophoresis is presented. A circuit model is developed for this purpose. The model parameters are fully defined in terms of the geometrical and material properties of the system. It is shown that trapping force can only be generated when the material properties follow certain impedance matching conditions. The impedance match factor is introduced to succinctly quantify the phenomenon. It is used to calculate bounds on the allowed electrical conductivity of the suspension medium. Results from the proposed model are found to be in good agreement with full-wave numerical simulations. By computing the acceptable set of material parameters with little computational cost, the presented analysis can streamline ODEP system design for various applications.

An optoelectronic tweezer (OET) device is presented that exhibits improved trapping resolution for a given optical spot size. The scheme utilizes a pair of patterned physical electrodes to produce an asymmetric electric field gradient. This, in turn, generates an azimuthal force component in addition to the conventional radial gradient force. Stable force equilibrium is achieved along a pair of antipodal points around the optical beam. Unlike conventional OETs where trapping can occur at any point around the beam perimeter, the proposed scheme improves the resolution by limiting trapping to two points. The working principle is analyzed by performing numerical analysis of the electromagnetic fields and corresponding forces. Experimental results are presented that show the trapping and manipulation of micro-particles using the proposed device.

When it comes to simulate or calculate an optoelectronic tweezer (OET) response for a microparticle suspended in a given medium, a precise electrical conductivity (later referred to as conductivity) value for the microparticle is critical. However, there are not well-established measurements or well-referenced values for microparticle conductivities in the OET realm. Thus, we report a method based on measuring the escape velocity of a microparticle with a standard OET system to calculate its conductivity. A widely used 6 μm polystyrene bead (PSB) is used for the study. The conductivity values are found to be invariant around 2×10-3 S/m across multiple different aqueous media, which helps clarify the ambiguity in the usage of PSB conductivity. Our convenient approach could principally be applied for the measurement of multiple unknown OET-relevant material properties of microparticle-medium systems with various OET responses, which can be beneficial to carry out more accurate characterization in relevant fields.

Lab-on-a-chip (LOC) devices capable of manipulating micro/nano-sized samples have spurred advances in biotechnology and chemistry. Designing and analyzing new and more advanced LOCs require accurate modeling and simulation of sample/particle dynamics inside such devices. In this work, we present a generalized computational physics model to simulate particle/sample trajectories under the influence of dielectrophoretic or optical forces inside LOC devices. The model takes into account time varying applied forces, Brownian motion, fluid flow, collision mechanics, and hindered diffusion caused by hydrodynamic interactions. We develop a numerical solver incorporating the aforementioned physics and use it to simulate two example cases: first, an optical trapping experiment, and second, a dielectrophoretic cell sorter device. In both cases, the numerical results are found to be consistent with experimental observations, thus proving the generality of the model. The numerical solver can simulate time evolution of the positions and velocities of an arbitrarily large number of particles simultaneously. This allows us to characterize and optimize a wide range of LOCs. The developed numerical solver is made freely available through a GitHub repository so that researchers can use it to develop and simulate new designs.