Large diameter, rigid monopile foundations have been extensively used in the fast-growing offshore wind energy industry over the last two decades. In view of the offshore environment, lateral response of the monopile usually governs its design. Even though several approaches have been recommended based on small-scale laboratory tests, there is no widely accepted method for the design of monopiles under lateral loading. Conversely, field testing on large-diameter prototype monopiles is normally impractical due to the high demand on the capacity of loading equipment. For these reasons a series of field lateral loading tests on reduced-scale monopiles were conducted at a dense sand test bed site. The model monopiles had similar aspect ratios of pile length to diameter to those used in the offshore wind farm projects, but were smaller in scale. Experimental curves were derived using the measured monopile responses of the lateral load tests, and a distinctive failure model was presented for monopiles in the overconsolidated dense sand deposit. Comparison of lateral responses of monopile between the measured and predicted by two current models showed the shear force at the pile tip plays an important role and should be accounted for in the design of laterally loaded rigid monopiles. Finally, a refined model for laterally loaded rigid monopiles in overconsolidated dense sand was recommended and calibrated.
4 June 2015 in Proceedings of the Institution of Civil Engineers - Geotechnical Engineering
Design models for offshore wind turbine monopiles tend to be based on those developed for flexible piles in the offshore oil and gas sectors. However, wind monopiles tend to be shorter and wider, resulting in a stiffer structure that rotates rather than bends when laterally loaded. New methods have been proposed to calculate the load–displacement response of piles to monotonic lateral loading. Those based on correlations with in situ tests such as the cone penetration test seem particularly promising. There is a dearth of experimental test data where monopiles have been subjected to extensive cyclic loading with which to extend such models to consider these effects. To address this, field tests were performed on two 340 mm diameter driven piles with an embedded length of 2·2 m, which were cyclically loaded with up to 5000 loading cycles. The piles had a slenderness ratio (embedded length over diameter) of 6·5, which is a typical value used in the offshore wind sector. The test results show that the accumulated pile head response primarily depends on the soil strength and stiffness, the previous loading history and loading characteristics. A cyclic loading design procedure consisting of cone penetration test based static design and Miner's rule based superposition is presented.
18 August 2017 in Bulletin of Engineering Geology and the Environment
Lateral force–displacement (P–y)-based Winkler spring models are commonly applied for the design of piles, P being the soil lateral reaction and y the lateral displacement. Despite their relative simplicity, P–y models can capture important aspects of pile behaviour including non-linear soil stiffness. Several P–y models based on cone penetration tests (CPTs) have been proposed over the last two decades, developed largely using empirical curve fitting to results of field tests, centrifuge modelling and finite-element analyses on relatively flexible piles installed in calcareous sand. However, major uncertainties exist when attempting to extrapolate empirical models for use with soil types and pile geometries outside the database on which they were formulated. There is an urgent need for a reliable P–y method for application to the design of rigid monopiles used extensively for offshore wind projects. A series of field lateral load tests performed on open-ended steel pipe piles driven in dense siliceous sand is reported here. The pile embedment length and load eccentricity were varied to investigate the behaviour of rigid and flexible monopiles. The measured pile response was used to evaluate the performance of a number of recent CPT-based P–y models and an update to an existing power-law model is suggested for rigid monopiles in siliceous sand. Lateral force–displacement (P–y)-based Winkler spring models are commonly applied for the design of piles, P being the soil lateral reaction and y the lateral displacement. Despite their relative simplicity, P–y models can capture important aspects of pile behaviour including non-linear soil stiffness. Several P–y models based on cone penetration tests (CPTs) have been proposed over the last two decades, developed largely using empirical curve fitting to results of field tests, centrifuge modelling and finite-element analyses on relatively flexible piles installed in calcareous sand. However, major uncertainties exist when attempting to extrapolate empirical models for use with soil types and pile geometries outside the database on which they were formulated. There is an urgent need for a reliable P–y method for application to the design of rigid monopiles used extensively for offshore wind projects. A series of field lateral load tests performed on open-ended steel pipe piles driven in dense siliceous sand is reported here. The pile embedment length and load eccentricity were varied to investigate the behaviour of rigid and flexible monopiles. The measured pile response was used to evaluate the performance of a number of recent CPT-based P–y models and an update to an existing power-law model is suggested for rigid monopiles in siliceous sand.
Piles are usually used as mooring or berthing dolphins in harbor to resist lateral loads mainly induced from ships’ impact, and as foundations for bridges and offshore structures (e.g. offshore wind turbines) to resist lateral and axial loads. During the design, the response of these piles to lateral loading should be analyzed, and in some circumstances, the lateral response governs the piles’ design. P-y curve method is the most popular approach and also is recommended by the offshore design standards/guidelines, such as American Petroleum Institute and Det Norske Veritas. However, the reliability of current P-y models is questionable when these models are employed to design a pile with dimensions beyond their originated field tests. In this study, firstly, field lateral loading tests on a rigid pile and a number of finite element analyses are comparably investigated. Then, a detailed evaluation of current P-y models is performed and discussed. Finally, a refined design guideline is presented for laterally loaded piles with a wider range of dimensions
In order to prevent possible charring, oxidation and (or) vaporisation of substances other than pore water, many researchers have adopted oven-drying temperature (t) values in the range 60–90°C for water content determinations of peat and other highly organic soils. This paper investigates the oven-drying characteristics of six very different highly decomposed peaty soils retrieved from south-west China for t values of 65, 85 and 105°C. Based on the presented experimental data, it is concluded that the standardised t value of 105°C used for testing of inorganic soil is also appropriate (and preferable to using lower t values) for routine water content determinations of these soils, which is in line with the growing consensus formed by other researchers on this topic. Further, the authors recommend a wet specimen mass of approximately 50 g and a 24 h oven-drying period in performing the oven-drying tests for t = 105°C. The paper also describes an existing approach to comparing and standardising water content values determined for the same organic soil, but on the basis of different t values, with the new data presented herein for the six Chinese soils used to strengthen its wider applicability in geotechnical engineering practice and related fields.