Objective: Polyetheretherketone (PEEK) is widely used as an orthopedic implant material owing to its good biocompatibility and mechanical strength; however, PEEK implants are biologically inert, resulting in suboptimal cellular responses after implantation. The aim of this study was to enhance the biological activity of PEEK through sulfonation treatment. Methods: In this study, distal phalangeal implants of PEEK were customized by fused deposition modeling (FDM) printing technology and soaked in concentrated sulfuric acid at different times to obtain sulfonated PEEK (SPEEK). The groups were divided into five groups according to the sulfonation time as follows: 0 min (control group), 1 min (group SPEEK1), 2 min (group SPEEK2), 4 min (group SPEEK4), and 8 min (group SPEEK8). Then the physicochemical characteristics of implants were determined by SEM, XRD, EDS, etc. The implants were co-cultured with stem cells from human exfoliated deciduous teeth (SHED), and then the cell proliferation, adhesion, alkaline phosphatase (ALP) activity, and alizarin red staining were performed to detect the biological activity, biocompatibility, and osteogenic activity of the SPEEK implants. Results: The sulfonation time range of 1 to 8 min could promote the formation of micropores on the surface of PEEK implants, while slightly affecting the composition and compression performance of the implants. Compared with the control group, the hydrophilicity of PEEK materials was not improved after sulfonation treatment. Tests for adhesion and proliferation of SHED indicated that SPEEK2 showed superior biocompatibility. Furthermore, ALP activity and semi-quantitative analysis of Alizarin red staining showed that the osteogenic activity of SPEEK2 phalanges exhibited significantly stronger osteogenic activity than the other groups. Conclusions: The method presented here provides a promising approach to improve the surface bioactivity of PEEK implants prepared by FDM, providing a shred of primary evidence to support the application of SPEEK in orthopedics.
Degradation of organic pollutants, especially organic dyes and antibiotics, by semiconductor photocatalysts is an efficient strategy for wastewater treatment. TiO2 nanomaterials are considered to be promising photocatalysts due to their high chemical stability, high efficiency and availability. Anatase TiO2 generally has superior photocatalytic activity to the rutile phase. However, the anatase phase can be irreversibly transformed to rutile phase when calcined at an elevated temperature. Methods to improve the stability of anatase are especially important for the TiO2 gas sensors working at high temperatures. The addition of strong acids can effectively suppress this transformation process. However, these strong acids are relatively expensive, corrosive and environmentally unfriendly. Herein, oxalic acid (OA) as a natural acid was used to control the hydrolysis process of tetrabutyl titanate (TBOT), leading to controllable crystalline phase transformation and reduced crystalline size of TiO2 on the nanoscale. What is more, the photocatalytic degradation performances were enhanced continuously when the molar ratio of OA to TBOT increased. The degradation reaction rate constants of CT650-R25 were about 10 times that of CT650-R0. The mechanism study shows that the enhanced photocatalytic activity can be attributed to the improved dispersibility, increased specific surface area and reduced recombination rates of photo-induced charge carriers and decreased energy bands as the concentration of OA increased. Thus, this work provides a simple, mild and effective method for controlling the crystalline forms of nano-TiO2 with enhanced photocatalytic performance towards waste water treatment.
16 January 2025 in Journal of Alloys and Compounds
We systematically study the low cycle fatigue behavior and its dependence of specific surface area ( ) for nanoporous copper (NPC) under ultrahigh strain rate ( s ) cyclic shear loading by conducting large-scale molecular dynamic simulation and small-angle x-ray scattering analysis. With an increase in , NPC undergoes a transition from the first excellent anti-fatigue property ( ) to the subsequent easy-to-fatigue capacity ( ). Two different mechanisms are governing fatigue: (i) smooth nucleation and propagation of dislocations for the former and (ii) nanopore compaction/coalescence for the latter by prohibiting the activities of dislocations. For NPC with , fatigue contributes to a surprising superelasticity, prompted by the entanglements and reversed disentanglements of longer dislocations. Surface reconstruction contributes to the fatigue tolerance of NPC by facilitating local surface roughening and the emission of dislocation slips, and it becomes more pronounced with decreasing .