The microstructure and mechanical properties of semisolid rheo-diecasting Al-xZn-2Mg-1.5Cu alloys with different Zn contents were investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), hardness testing (HV) and room temperature tensile testing. Results show that the as-cast microstructure mainly consists of spherical α-Al and Mg(Al, Cu, Zn)2 phases. Furthermore, a small amounts of Al7Cu2Fe phases were also detected along the grain boundary. Increasing the Zn contents from 8–12%, the volume fraction of the Mg(Al, Cu, Zn)2 phases increases from 4.9–7.4%. After solution heat treatment at 470 °C for 8 h, most of the Mg(Al, Cu, Zn)2 dissolves into the α-Al matrix, while the Al7Cu2Fe phase keeps with remains. The yield strength linearly increases from 482 ± 5 MPa of 8% Zn to 529 ± 5 MPa of 12% Zn. While, the ultimate strength of 10% Zn is 584 ± 2 MPa, which is higher than that of the other two alloys. Moreover, the average elongation dramatically decreases from 13% for the 8% Zn alloy to 2% for the 12% Zn alloy.
This study aims to bridge the critical knowledge gap in understanding the dynamic microstructural evolution during high-solid-fraction semi-solid rheo-die casting process, including slurry preparation (0.1–0.3 K/s) and rheo-die casting (10–150 K/s). A novel phase-field model coupling continuous cooling with explicit nucleation was developed, enabling the dynamic simulation of continuous solidification microstructure evolution, considering two-stage cooling rate transition characteristics. Integrated the Swirled Enthalpy Equilibration Device (SEED) slurry preparation and graded-cooling mold experiments established variable cooling rate and solid fraction conditions for quantitative analysis of α-Al morphological evolution during rheo-die casting solidification. Through experimental and simulation investigations of the Al-7Si alloy, it is concluded that during Stage I slurry preparation, the primary α1-Al phase coarsened due to Ostwald ripening. In Stage II rheo-die casting, primary α1-Al undergoes continued growth under a moderate cooling rate (15 K/s). Meanwhile, secondary α2-Al formation exhibits a cooling-rate and solid fraction dependence: a high cooling rate (150 K/s) promotes explosive nucleation with the volume fraction decreasing from 4.78% to 0.33% as the solid fraction rises, whereas a mid-cooling rate (15 K/s) substantially suppresses its formation. Mechanistically, a high cooling rate promotes solute trapping, which intensifies constitutional undercooling, thereby elevating both the nucleation and growth driving forces to facilitate the formation of secondary α2-Al, whereas higher solid fractions restrict secondary phase formation by narrowing the solidification windows from 22 °C to 7 °C.
13 May 2025 in Journal of Materials Engineering and Performance
Squeeze casting is an advanced technology to produce aluminum alloy components with excellent mechanical property. Due to good fluidity and castability, the Al-Si alloy is the most common aluminum material in squeeze casting. However, the segregation in solid α-Al phase and liquid eutectic Si phase happens during solidification, which leads to microstructural inhomogeneous in the final microstructure. In this study, the eutectic Si segregation of Al-12Si-1Cu alloy under different intensification pressure in squeeze casting was investigated by Optical Microscopy (OM). The results show that increasing intensification pressure promotes the eutectic Si segregation at center zone, while the eutectic Si phase at skin zone is not much influenced. Increasing the intensification pressure from 65 MPa to 140 MPa, the segregation degree of eutectic Si at center zone increases from 0.05 to 0.29, while the segregation degree at skin zone levels at 0.2. Under high intensification pressure, the feeding effect of liquid phase at center zone is prominent, which results to high tendency of eutectic Si segregation in the final microstructure.
1 March 2026 in Journal of Physics: Conference Series
This study develops a multiscale modeling framework integrating finite element simulation, CALPHAD thermodynamics, and phase-field modeling to investigate microstructural evolution during semi-solid slurry preparation of Al-7Si alloy via the SEED process. The established non-isothermal phase-field model dynamically couples temperature and concentration distributions, updating solute partition coefficients and interfacial equilibrium concentrations in real-time through CALPHAD computation. Adapted to actual process scales, By integrating boundary conditions derived from finite element simulations—including cooling rates and CALPHAD-coupled thermodynamic parameters—we established a thermo-kinetic multiscale modeling framework that bridges macroscopic temperature evolution with mesoscopic phase-field simulations. The model successfully simulates hundreds of seconds of microstructure evolution, encompassing the entire slurry preparation process. Combined with experimental validation, this approach accurately reproduces the dynamic evolution of temperature and concentration distributions during continuous cooling, significantly improving the predictability of competitive growth and spheroidization mechanisms in multi-grain systems.