Hollow fiber membranes of polyvinylidene fluoride (PVDF) were prepared by incorporating varying concentrations of hydrophilic surface-modifying macromolecules (LSMM) and a constant amount of polyethylene glycol (PEG) additives. The membranes were fabricated by the dry-wet spinning technique. The prepared hollow fiber membranes were dip-coated by hydrophobic surface-modifying macromolecules (BSMM) as the final step fabrication. The additives combination is aimed to produce hollow fiber membranes with high flux permeation and high salt rejection in the matter of seawater desalination application. This study prepares hollow fiber membranes from the formulation of 18 wt. % of PVDF mixed with 5 wt. % of PEG and 3, 4, and 5 wt. % of LSMM. The membranes are then dip-coated with 1 wt. % of BSMM. The effect of LSMM loading on hydrophobicity, morphology, average pore size, surface porosity, and membrane performance is investigated. Coating modification on LSMM membranes showed an increase in contact angle up to 57% of pure, unmodified PVDF/PEG membranes, which made the fabricated membranes at least passable when hydrophobicity was considered as one main characteristic. Furthermore, The PVDF/PEG/4LSMM-BSMM membrane exhibits 161 °C of melting point as characterized by the DSC. This value indicates an improvement of thermal behavior shows so as the fabricated membranes are desirable for membrane distillation operation conditions range. Based on the results, it can be concluded that PVDF/PEG membranes with the use of LSMM and BSMM combination could enhance the permeate flux up to 81.32 kg·m−2·h−1 at the maximum, with stable salt rejection around 99.9%, and these are found to be potential for seawater desalination application.
1 July 2021 in Korean Journal of Materials Research
A membrane chitosan with silica from rice husk ash was fabricated as alternative membrane electrolyte for direct methanol fuel cell (DMFC) application. Chitosan is made from shrimp shell powder which is processed through deproteination, demineralization and deacetylation steps. Furthermore, the phase diversion technique was used to synthesis membranes by mixing chitosan and silica in acetic acid solution. The resultant membrane characterized with FTIR, water and methanol uptake, ion exchange capacity, and methanol permeability. FTIR analysis showed that chitosan and silica was successfully synthesized. Water uptake for the chitosan-silica membrane increased with increasing silica loading, but the methanol uptake value decreased. The chitosan-silica with 15 wt% silica loading exhibited the best ion exchange capacity and methanol permeability which were 1.290 meq/gram and 2.42 x 10−4 cm2/s, respectively. All the result obtained from this studi shown that chitosan-silica membrane is a promising electrolyte membrane for direct methanol fuel cell application.
18 December 2022 in International Journal of Marine Engineering Innovation and Research
One way to reduce the scarcity of fuel oil is to make environmentally friendly alternative fuels such as biodiesel. The utilization of biodiesel can be a new energy source and also help reduce the excessive use of fuel, especially diesel and diesel oil in Indonesia. In Indonesia, the amount of palm oil will reach 49.7 tons by 2021, and this data is up 2.9% from the pre-vious year. Palm fruit is processed into CPO. More palm oil processing will produce waste called POME (Palm Oil Mill Effluent). The diesel engine transesterification method is suitable for the manufacture of biodiesel. The amount of base on the catalyst's surface affects the catalyst's activity. So that the higher the base value on the catalyst, the higher the yield of biodiesel that will be produced. The biodiesel produced will be tested on a 4-stroke diesel engine with a B5 and B10 blending composition. The study's results showed that the density and viscosity values for B5 were 5.8 cSt and 810 Kg/m3 and for B10 were 6.3 cSt and 860 Kg/m3. As for engine performance, power, torque, and SFC for B5 fuel at 4000-watt load conditions and 1000 Rpm, engine speeds are 1.18 Kw, 11.28 Nm, and 256.8 gr/Kw. B10 at 4000-watt load condition and 1000 Rpm engine speed is 1.16 Kw, 11.12 Nm, and 269.2 gr/Kw.
1 January 2021 in Journal of Physics: Conference Series
This research aims to know the effects of extract composition on the solid soap properties (i.e. pH and hardness). The extract composition and reaction time were varied at 1 to 1.5 wt.% and 20 to 40 minutes, respectively. The red dragon fruit peels (Hylocereus polyrhizus) extract was obtained by maceration method followed by evaporation process, in order to remove the remaining ethanol (EtOH). The solid soap is made by reacting Virgin Coconut Oil (VCO) with sodium hydroxide (NaOH) and several additives. The results showed that the prepared solid soaps contain pH (8.29 – 10), hardness (55.763 – 380.167 mm/s). It indicates that solid soap with reaction time 20 minutes with 1.5 wt.% extract has the best stability among all the formed soaps.
29 April 2024 in Jurnal Teknik Kimia dan Lingkungan
Coke, an essential ingredient in the steel and metallurgical industries, is typically derived from bituminous coal. However, in Indonesia, where bituminous coal is rare, coke production is dependent on coal imports due to the high moisture content of local coal. An alternative approach is to use biomass, such as palm oil processing waste, for "biomass coke" to produce a more environmentally friendly coke with lower greenhouse gas emissions. Palm kernel shell waste rich in lignocellulose proved suitable for this purpose due to its compressive strength and carbon content. Pyrolysis, a technique for creating porous micro-structured carbon from palm kernel shells, was used to produce this coke substitute, offering a more sustainable energy source with a lower carbon footprint than fossil fuels. Bio-coke exhibits low moisture content (5.84%) and ash content (13.20%) due to the moisture and ash reduction effects of bondcrete adhesive during combustion. It also demonstrates substantial compressive strength (14 mPa), a high calorific value (6795 cal/g), and a favorable pore structure with a large surface area, indicating a positive influence of bondcrete adhesive on coke properties without compromising energy potential.