Norbert Krisztián Kovács

Dr. Norbert Krisztián Kovács

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

4 September 2015 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Closed access
PDF file
TTTamás Tábi
Tamás Tábi
NKNorbert Krisztián Kovács
Norbert Krisztián Kovács
ISI. E. Sajó
I. E. Sajó
TCTibor Czigany
Tibor Czigany
SHS. Hajba
S. Hajba
JKJ. G. Kovács
J. G. Kovács

1 June 2015 in Applied Thermal Engineering
Verified
Journal Article
Open access
József Gábor KovácsJózsef Gábor Kovács
József Gábor Kovács
FSFerenc Szabó
Ferenc Szabó
NKNorbert Krisztián Kovács
Norbert Krisztián Kovács
ASAndrás Suplicz
András Suplicz
BZBéla Zink
Béla Zink
HHHajnalka Hargitai
Hajnalka Hargitai

22 February 2017 in Polymers
Verified
Journal Article
Open access
PDF file
BZBéla Zink
Béla Zink
FSFerenc Szabó
Ferenc Szabó
Istvan HatosIstvan Hatos
Istvan Hatos
ASAndrás Suplicz
András Suplicz
NKNorbert Krisztián Kovács
Norbert Krisztián Kovács
József Gábor KovácsJózsef Gábor Kovács
József Gábor Kovács
The most time-consuming phase of the injection molding cycle is cooling. Cooling efficiency can be enhanced with the application of conformal cooling systems or high thermal conductivity copper molds. The conformal cooling channels are placed along the geometry of the injection-molded product, and thus they can extract more heat and heat removal is more uniform than in the case of conventional cooling systems. In the case of copper mold inserts, cooling channels are made by drilling and heat removal is facilitated by the high thermal conductivity coefficient of copper, which is several times that of steel. Designing optimal cooling systems is a complex process; a proper design requires injection molding simulations, but the accuracy of calculations depends on how precise the input parameters and boundary conditions are. In this study, three cooling circuit designs and three mold materials (Ampcoloy 940, 1.2311 (P20) steel, and MS1 steel) were used and compared using numerical methods. The effect of different mold designs and materials on cooling efficiency were examined using calculated and measured results. The simulation model was adjusted to the measurement results by considering the joint gap between the mold inserts.

1 August 2019 in International Journal of Pharmaceutics
Verified
Journal Article
Closed access
KIKinga Ilyés
Kinga Ilyés
ABAttila Balogh
Attila Balogh
Tibor CasianTibor Casian
Tibor Casian
TITamás Igricz
Tamás Igricz
EBEnikő Borbás
Enikő Borbás
ZNZsombor Kristóf Nagy
Zsombor Kristóf Nagy

21 June 2024 in Polymer Composites
Verified
Journal Article
Open access
CTCsenge Tóth
Csenge Tóth
NLNorbert László Lukács
Norbert László Lukács
NKNorbert Krisztián Kovács
Norbert Krisztián Kovács
In this study, we investigate the relationship between structure and properties of fiber–matrix adhesion for material extrusion–based 3‐dimensional (3D) printed composites. We examine the influence of fiber length and fiber content on the tensile properties of glass, basalt, and carbon fiber–reinforced polylactic acid (PLA) composites. Short fiber–reinforced filaments were produced, then, simple micromechanical models were used to predict the in‐plane tensile properties. We found that interlayer tensile properties are strongly influenced by fiber–matrix adhesion. If adhesion is sufficient, the fibers and matrix deform together under tensile load. A second‐order relationship describes interlayer tensile strength in relation to fiber content between 5 and 25 w%, with a maximum at 15 w%, for carbon and basalt fiber–reinforced composites. If adhesion is weak, the crack propagates along the fiber–matrix interface, causing brittle fracture and low strength. This behavior was noted for the glass fiber composite, for which the calculated interface shear strength was the lowest (1.4 MPa). In this case, fiber content is inversely proportional to interlayer tensile strength. Our results show the role of fiber–matrix adhesion quality on tensile properties, which has a major impact on both the accuracy of predictions and the damage processes.Highlights: Critical fiber length determines accuracy of tensile property estimates Quality of fiber–matrix adhesion governs interlayer damage process Poor adhesion causes brittle fracture and low strength Second‐order relationship of interlayer tensile strength and fiber content Loss of interlayer tensile strength in composite due to fiber–matrix interface