Matthias Franz Rath

Mr. Matthias Franz Rath


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 December 2021 in Sensors
Verified
Journal Article
Open access
PDF file
MRMatthias Franz Rath
Matthias Franz Rath
BSBernhard Schweighofer
Bernhard Schweighofer
Hannes WegleiterHannes Wegleiter
Hannes Wegleiter
The strain in a fast spinning carbon fiber flywheel rotor is of great interest for condition monitoring, as well as for studying long-term aging effects in the carbon fiber matrix. Optoelectronic strain measurement is a contactless measurement principle where a special reflective pattern is applied to the rotor which is scanned by a stationary optical setup. It does not require any active electronic components on the rotor and is suited for operation in a vacuum. In this paper, the influences of the key parts comprising the optoelectronic strain measurement are analyzed. The influence of each part on the measurement result including the uncertainty is modeled. The total uncertainty, as well as each part’s contribution is calculated. This provides a valuable assessment of requirements for component selection, as well as tolerances of mechanical parts and processes to reach a final target measurement uncertainty or to estimate the uncertainty of a given setup. We have shown that the edge quality of the special reflective pattern has the strongest influence, and how to improve it. Considering all influences, it is possible to measure strain with an uncertainty of less than 1% at a rotation speed of 500Hz.

1 August 2023 in IEEE Sensors Letters
Verified
Journal Article
Open access
MRMatthias Franz Rath
Matthias Franz Rath
BSBernhard Schweighofer
Bernhard Schweighofer
Hannes WegleiterHannes Wegleiter
Hannes Wegleiter
The main component of flywheel energy storage systems (FESS) is the flywheel rotor itself - a rotating mass which stores kinetic energy. Ongoing research in the field of FESS requires constant condition monitoring of the flywheel rotor, especially when new composite materials and flywheel rotor manufacturing methods are investigated. Optoelectronic strain measurement (OESM) is a method to contactlessly measure the flywheel rotor's radial deformation as well as its position in the radial plane via a special reflective pattern on the flywheel which is read via optical sensors. This paper presents a simulation model to estimate the influence of pattern offset and in-plane movement of the flywheel on an array of multiple sensors. The measurement values from multiple sensors can be fused to mitigate the influence of cross sensitivity between flywheel deformation and position measurements. The influence of out-of-plane movement on the measured values is evaluated via measurements on a test bench setup where the sensor distance can be controlled by a stepper motor.

1 July 2024 in Sensors
Verified
Journal Article
Open access
PDF file
MRMatthias Franz Rath
Matthias Franz Rath
CBChristof Birgel
Christof Birgel
Armin BuchroithnerArmin Buchroithner
Armin Buchroithner
BSBernhard Schweighofer
Bernhard Schweighofer
Hannes WegleiterHannes Wegleiter
Hannes Wegleiter
Monitoring the strain in the rotating flywheel in a kinetic energy storage system is important for safe operation and for the investigation of long-term effects in composite materials like carbon-fiber-reinforced plastics. An optoelectronic strain-measurement system for contactless deformation and position monitoring of a flywheel was investigated. The system consists of multiple optical sensors measuring the local relative in-plane displacement of the flywheel rotor. A special reflective pattern, which is necessary to interact with the sensors, was applied to the surface of the rotor. Combining the measurements from multiple sensors makes it possible to distinguish between the deformation and in-plane displacement of the flywheel. The sensor system was evaluated using a low-speed steel rotor for single-sensor performance investigation as well as a scaled-down high-speed rotor made from PVC plastic. The PVC rotor exhibits more deformation due to centrifugal stresses than a steel or aluminum rotor of the same dimensions, which allows experimental measurements at a smaller flywheel scale as well as a lower rotation speed. Deformation measurements were compared to expected deformation from calculations. The influence of sensor distance was investigated. Deformation and position measurements as well as derived imbalance measurements were demonstrated.