Rotorcrafts experience severe vibrations during operation. To ensure the safety of rotorcrafts, it is necessary to perform anomaly detection to detect small-scale structural faults in major components. To accurately detect small-scale faults before they grow to a fatal size, HR (high sampling rate) vibration data are required. However, to increase the efficiency of data storage media, only LR (low sampling rate) vibration data are generally collected during actual flight operation. Anomaly detection using only LR data can detect faults above a certain size, but may fail to detect small-scale faults. To address this problem, we propose an anomaly detection technique using the SR3 (Super-Resolution via Repeated Refinement) algorithm to upscale LR data to HR data, and then applying the LSTM-AE model. This technique is validated for two datasets (drone arm data, CWRU bearing data). First, the necessity for HR data is illustrated by showing that anomaly detection using LR data fails, and the upscaling performance of the SR3 algorithm is validated in the frequency and time domain. Finally, the anomaly detection for a structural fault diagnosis is performed for the upscaled data and the HR data using the LSTM-AE model. The quantitative evaluation of the Min–Max normalized reconstruction error distribution is performed through the MSE (Mean Square Error) value of the anomaly detection results. As a result, it is confirmed that the anomaly detection using upscaled test data can be performed as successfully as the anomaly detection using HR test data for both datasets by the proposed technique.
Lattice structures, composed of interconnected struts, offer an efficient way to reduce structural weight while maintaining structural integrity. Because of this potential, this work aims to investigate and develop an efficient variant form of a BCC (Body-Centered Cubic) lattice structure to enhance the structural robustness and energy absorption capability, based on the Maxwell stability criterion. And we specifically changed the bending-dominated to stretching-dominated behavior by adding auxiliary struts, according to the theory, and confirmed how this affects the compression behavior of the structure. For this purpose, horizontal auxiliary struts are added for the first time to the BCC structure along with vertical struts. As a macroscale cellular lattice structure, a unit cell size of 12 mm is considered. For the considered macroscale cellular lattice structures, FEA (finite element analysis) is employed to numerically investigate the stress distribution and compressive deformation mechanisms. Then, quasi-static compression tests are carried out to measure the energy absorption performance of the lattice structures manufactured by the EBM (Electron Beam Melting) metal additive manufacturing technique, which has advantages in building lattice structures without supporters. A comprehensive investigation reveals that a newly designed lattice structure offers significant advantages in structural robustness, with energy absorption capability increased by 365% compared to existing structures, achieved by incorporating vertical and cross-shaped horizontal auxiliary struts into the original BCC lattice configuration. The enhanced lattice structures can be utilized in industries where low-weight and high-strength are needed, such as aerospace, marine, and other industries.
The development of advanced air mobility—an eco-friendly, next-generation transportation system—is underway and garners significant attention. Due to the novel propulsion concept of eVTOL (electric Vertical Take-Off and Landing) and its operation in low altitude, urban environment, regulations for commercialization have not yet been established. Consequently, related research on passenger safety in emergency landings is ongoing, and this study focuses on enhancing the crashworthiness of advanced air mobility. To ensure the crashworthiness of advanced air mobility, civil airworthiness standards were referenced to determine the appropriate test conditions, and a design criterion for developing an energy-absorbing structure was derived. In this study, lattice structures are considered for designing an energy-absorbing structure that satisfies the design criterion, and finite element analysis is conducted to predict the performance of lattice structures. Based on the predicted data, surrogate models are constructed using the Kriging method according to the type of lattice structure. To verify the data obtained from numerical models, representative structures are manufactured using EBM (Electron Beam Melting) technology, and compressive tests are conducted to obtain the force–displacement curves. The test data are compared with the numerical data, and it is confirmed that the test data show good agreement with the numerical data. After this confirmation, the constructed surrogate models are utilized to select a lattice-based energy-absorbing structure that satisfies the crashworthiness-related design criterion. Finally, a crash simulation of a vertical drop test is carried out using the selected lattice structure, and results indicate that the resulting acceleration due to the collision is below the human tolerance limit, thereby verifying the crashworthiness of the energy-absorbing structure.
Electrohydrodynamic (EHD) inkjet printing is an efficient technique for printing multiple sensors in a multifaceted area. It can be applied to various fields according to the shape of the printing result and the algorithm employed. In this study, temperature sensors capable of detecting heat sources were fabricated. Inks suitable for EHD inkjet printing were produced, and optimal parameters for printing were determined. Printing was performed using the corresponding parameters, and various printing results were obtained. Furthermore, an experiment was conducted to confirm the temperature measurement characteristics of the results and the tolerance of the sensor. Grid-type sensors were fabricated based on the results, and the sensor characteristics were confirmed in an orthogonal form. Heat was applied to arbitrary positions. Resistance to changes due to heat was measured, and the location at which the heat was generated was detected by varying the change in resistance. Through this study, efficient heat control can be achieved, as the location of the heat source can be identified quickly.
9 May 2023 in International Journal of Aeronautical and Space Sciences