Finite element numerical simulation calculation of pavement structure load response is widely applied; however, there is still a lack of research on the polyurethane (PU) mixture composite pavement load response. The mechanical characteristics of PU mixture composite pavement are not well understood, and there is a lack of research on typical pavement structures of PU mixtures, which limits their application in pavement structures. Therefore, herein, the mechanical properties of PU mixtures are analysed using the dynamic modulus test, uniaxial penetration test, and fatigue test. Further, the finite element theory calculation method is used to realize the load response calculation of orthogonal design composite pavement structure. The results show that PU mixtures exhibit more obvious elastic characteristics and have good shear resistance, fatigue stability, and temperature stability, and can be used as shear and anti-fatigue layers. The structure of ‘4 cm SMA-13 + 5 cm PUM-20 + 6 cm PUM-25 + semi-rigid base’ is recommended for the PU mixture composite structure. In comparison to typical asphalt pavement, the analysis shows that except for shear stress, temperature has little effect on the load response of PU composite pavement structures, while high temperatures lead to a significant increase in the load response of typical asphalt pavement structures. The PU composite pavement can bear greater loads and has a reduced thickness of its surface layer by about 3 cm in comparison to conventional pavement. The results of this study provide theoretical support for the design of PU mixture pavement structures and promote the popularization and application of PU mixture pavement.
The water inrush of the Shangjiawan karst tunnel is used to study the evolution pattern of precursor water inrush information in water-filled caves and to further reveal the matching mode of the information. The three-dimensional numerical method FLAC3D was used to simulate the evolution process of water inrush after damage to a water-blocking rock mass structure in a water-filled cave and to obtain the evolution pattern of precursor water-inrush information caused by the damage. The results show that the multifield response to the characteristic precursor information of the water-inrush pattern after the fracture of the water-blocking rock mass follows the order of stress-field displacement-field seepage-field. Further, the matching pattern of the information shows that the stress field increased first and then decreased, the displacement field always increased, and the seepage field increased first and then decreased.
The interlaminar shear characteristics of a polyurethane (PU) mixture composite structure, quantitatively calculating its energy consumption and carbon emissions were analyzed in this study. Inclined shear tests were carried out on thirteen structures without interlaminar treatment, and high-temperature water bath accelerated loading tests were conducted on three composite structures; further, the interlaminar shear strength of the tire trace position after the accelerated loading test was tested to analyze the influence of both the high-temperature water bath environment and loading on the structure. In addition, based on the medium repair project of the Qingdao-Yinchuan expressway, the construction log of PU mixture pavement and asphalt pavement was investigated. Combined with the calculation parameters provided by the United Nations Intergovernmental Panel on Climate Change (IPCC), the consumption and carbon emissions of the two types of mixtures were calculated and compared quantitatively. The results showed that the shear strength between layers of asphalt mixtures, PU mixture and asphalt mixture was less than 2 MPa; however, the shear strength between PU mixture–cement-stabilized macadam and PU mixture–PU mixture was greater than 3 MPa. Therefore, it was recommended to spread a 0.4 L/m2 two-component PU adhesive layer as the interlayer treatment scheme for the structure of asphalt mixture-PU mixture and PU mixture-asphalt mixture; the high-temperature water area and accelerated loading had different effects on the interlaminar shear strength of the three structures. The PUM-16 mixture could effectively reduce energy consumption by 88.3 and 87.2%, carbon emissions by 81.1% and 79.1% in comparison to Stone Matrix asphalt with Nominal maximum particle size of 13.2 mm (SMA-13) and Stone Matrix asphalt with Nominal maximum particle size of 19.0 mm (SMA-20). Thus, the PU mixture was confirmed to be an environmentally friendly road pavement material.
The extent to which drivers’ collision avoidance maneuvers affect the safety margins of sideslip and rollover is not captured by road geometric design theory. To quantify the effects of drivers’ collision avoidance maneuvers on the safety margins of sport utility vehicles (SUVs) on horizontal curve and grade combinations, a modified 8-degree-of-freedom multibody model based on SUVs was developed. The model was then used to calculate the design safety margins of sideslip and rollover for steady states and the actual safety margins for collision avoidance maneuvers. Subsequently, the design safety margin reduction rate (the difference between the design and actual safety margins divided by the design safety margin) was calculated and used to assess the safety margins. The results showed that the safety margins of SUVs were significantly reduced by braking, lane changing, and lane changing with braking. The marginal effects indicated that the greater the deceleration and the shorter the lane change duration, the greater the effect on the safety margins, particularly the sideslip safety margin. Furthermore, when the SUV was driven at 80 km·h−1 on grades with a horizontal curve radius of 270 m and 400 m, the sideslip safety margin with emergency braking (deceleration over −4.5 m·s−2) was reduced by 71% and 21%, and the rollover safety margin was reduced by 11% and 5%, respectively. Under these conditions, an emergency lane change (lane change duration less than 2 s) caused the SUV to sideslip and reduced the rollover safety margin by 47% (curve radius 270 m) and 45% (curve radius 400 m). Therefore, drivers’ collision avoidance maneuvers are a factor that cannot be neglected in alignment design.
The design hourly volume (DHV) of traffic based on the 30th highest hourly volume (30 HV) of the year has been widely applied in expressway design in various countries to balance the benefit and economy of expressway engineering. However, this design method has barely changed since it was first adopted in China, which may be contrary to the rapidly changing traffic macroenvironment. In this study, annual hourly traffic volume (HV) data pertaining to expressways in East China, Southwest China and Northwest China were collected. Based on the descending order of the obtained HV and HV factor data, the distribution patterns of the traffic demand throughout the year and peak hours were analyzed. The distribution characteristics of the HV, typicality of 30 HV and applicability of the DHV factor were investigated. It was found that severe polarization occurred in the HV distribution in China. The actual 30 HV factor is more than 0.5 times the recommended value in the specification. Continued use of the current DHV would result in more than 200 h of inefficient travel time, 5.7 times more than expected, with the DHV factor is currently no longer applicable in China. Furthermore, the annual 30 HV value loses its typical status. Depending on the level of local economic development, using 10 HV factor or 80 HV factor as the new DHV factor can better alleviate the congestion problem. This study determines the reasons for the widespread congestion issues in China from the perspective of expressway design, which is beneficial to adjust the basis of expressway design in China.
An unreasonable design hourly volume (DHV) greatly impacts road facility construction costs and traffic efficiency. With the rapid rise in the tourism economy and widespread emergence of holiday travel characteristics in China, DHV applicability for suburban expressways requires verification. This study collected annual traffic volume data over 8760 h along Xi’an Ring Expressway from 2017 to 2019. Traffic demand distribution patterns throughout the year and peak hours were analyzed on the basis of the descending order of the obtained hourly traffic volume (HV) and factor data. HV distribution characteristics, 30th highest hourly volume (30 HV) typicality, and DHV factor applicability were investigated. Due to travel characteristics under the background of the tourism economy, the peak HV distribution exhibits polarization characteristics. The recommended value of the design hour traffic factor in the specification corresponded to a number of hours greater than 200, with the 30 HV factor under the background of the tourism economy being 25% higher than the recommended value. Considering the tourism economy, the high level of traffic operation time increased significantly, and the characteristics of a sharp decline in the peak HV disappeared. The 30 HV factor no longer exhibited traditional characteristics. The design causes of traffic congestion are identified herein.