Carrier-free spray-dried dispersions for pulmonary delivery, for which the demand is growing, frequently require the incorporation of dispersibility-enhancing excipients into the formulations to improve the efficacy of the dosage form. One of the most promising of such excipients, L-leucine, is expected to be approved for inhalation soon and has been studied exhaustively. However, during stability, small fibers protruding from the particles of leucine-containing powders have occasionally been observed. To clarify the origin of these fibers and assess their potential influence on the performance of the powders, three different classes of spray-dried leucine-containing formulation systems were studied over an 8-month accelerated stability program. These systems consisted of a large molecule biologic (bevacizumab) in conjunction with a glass former (trehalose), an amorphous small-molecular mass active (moxidectin), and a crystallizing active (mannitol). It was determined that the appearance of the fibers was due to the presence of small quantities of leucine in higher energy states, either because these were amorphous or present as a less stable crystalline polymorph. It was further shown that the growth of these leucine fibers caused no significant physicochemical instability in the powders. Nor, more importantly, did it decrease their aerosol performance in a dry powder inhaler or reduce the concentration of their active pharmaceutical ingredients.
Spray drying is a particle engineering technique used to manufacture respirable pharmaceutical powders that are suitable for delivery to the deep lung. It is amenable to processing both small molecules and biologic actives, including proteins. In this work, a simultaneous spray-drying process, termed simul-spray, is described; the process involves two different active pharmaceutical ingredient (API) solutions that are simultaneously atomized through separate nozzles into a single-spray dryer. Collected by a single cyclone, simul-spray produces a uniform mixture of two different active particles in a single-unit operation. While combination therapies for dry powder inhalers containing milled small molecule API are commercially approved, limited options exist for preparing combination treatments that contain both small molecule APIs and biotherapeutic molecules. Simul-spray drying is also ideal for actives which cannot withstand a milling-based particle engineering process, or which require a high dose that is incompatible with a carrier-based formulation. Three combination case studies are demonstrated here, in which bevacizumab is paired with erlotinib, cisplatin, or paclitaxel in a dry powder inhaler formulation. These model systems were chosen for their potential relevance to the local treatment of lung cancer. The resulting formulations preserved the biologic activity of the antibody, achieved target drug concentration, and had aerosol properties suitable for pulmonary delivery.
Many active pharmaceutical ingredients (APIs) in the pharmaceutical pipeline require bioavailability enhancing formulations due to very low aqueous solubility. Although spray dried dispersions (SDDs) have demonstrated broad utility in enhancing the bioavailability of such APIs by trapping them in a high-energy amorphous form, many new chemical entities (NCEs) are poorly soluble not just in water, but in preferred organic spray drying solvents, e.g., methanol (MeOH) and acetone. Spraying poorly solvent soluble APIs from dilute solutions leads to low process throughput and small particles that challenge downstream processing. For APIs with basic pKa values, spray solvent solubility can be dramatically increased by using an acid to ionize the API. Specifically, we show that acetic acid can increase API solubility in MeOH:H2O by 10-fold for a weakly basic drug, gefitinib (GEF, pKa 7.2), by ionizing GEF to form the transient acetate salt. The acetic acid is removed during drying, resulting in a SDD of the original GEF free base having performance similar to SDDs sprayed from solvents without acetic acid. The increase in solvent solubility enables large scale manufacturing for these challenging APIs by significantly increasing the throughput and reducing the amount of solvent required.
7 March 2023 in International Journal of Pharmaceutics
Glycerides are widely employed as solid matrices in a range of pharmaceutical intermediates and dosage forms. Diffusion-based mechanisms are responsible for drug release, with both chemical and crystal polymorph differences in the solid lipid matrix cited as controlling factors in drug release rates. This work uses model formulations composed of crystalline caffeine embedded in tristearin to study the impacts to drug release from the two primary polymorphic states of tristearin and dependencies on the conversion routes between them. Using contact angles and NMR diffusometry, this work finds that drug release from the meta-stable α-polymorph is rate limited by a diffusive mechanism relating to its porosity and tortuosity, but initial burst release occurs due to ease of initial wetting. Poor wettability resulting from surface blooming can be rate limiting for the β-polymorph, resulting in slower initial drug release relative to the α-polymorph. The route to achieve the β-polymorph strongly impacts the bulk release profile due to differences in crystallite size and packing efficiency. API loading enhances the effective porosity, leading to enhanced drug release at high loadings. These findings offer generalizable principles to guide formulators on the types of impacts to drug release rates that one may expect due to triglyceride polymorphism.