Vibration impulses caused by surface defects of railway vehicle axle-box bearings are important features for fault diagnosis. To accurately diagnose axle-box bearing surface defects, robust blind deconvolution (BD) methods are proposed to extract defect-induced repetitive impulses from axle-box vibration measurements in this article. Specifically, a unified theoretical framework for the BD methods using time-domain and frequency-domain generalized statistical indicators as objective functions is established respectively by converting the deconvolution problem into a generalized Rayleigh quotient-based generalized eigenvalue problem. On this basis, two new BD methods for extracting repetitive impulse features are presented by employing the robust power function-based Gini index as the objective function. They obtain optimal deconvolution filters by adaptively evaluating repetitive transient features in the squared envelope and squared envelope spectrum of the filtered signal, respectively. The developed methods are verified on bench experimental signals of manufactured and naturally occurring axle-box bearing faults. The results show that the presented BD methods can effectively enhance repetitive impulse features and diagnose various defects of railway vehicle axle-box bearings.
Active vibration suppression of high-speed electric multiple unit (EMU) car bodies was studied by the combined use of secondary suspension actuators and piezoelectric actuators. A vertical dynamics model was established considering secondary suspension actuators and piezoelectric actuators. The positions of the piezoelectric actuators and sensors were optimized using $H_{2} $ and $H_{\infty } $ norms. The feedback controller was designed using a robust optimal control method. The effects of the vibration devices and active control methods on the vehicle dynamic performance were simulated using MATLAB. The dynamic performance differences among the passive suspension vehicle, secondary vertical actuator installation vehicle, and active vibration control vehicle were compared and analyzed. The results show that the piezoelectric actuators and piezoelectric sensors were arranged at distances of 7.15, 12.25, and 17.35 meters from the left end of the car body, and the normalized $H_{2} $ and $H_{\infty } $ norms of the first and second order elastic modes of the car body were the largest, which can be used as piezoelectric actuators and sensor placement positions. Secondary suspension actuators can reduce rigid car body vibrations, and piezoelectric actuators can reduce elastic vibration. The higher the speed, the better is the acceleration suspension effect. When the vehicle speeds were 200 km $\cdot \text{h}^{-1}$ and 350 km $\cdot \text{h}^{-1}$ , the vehicle vibration acceleration decreased by 10% and 18%, respectively. Compared with the passive suspension system, the active vibration suspension system with a robust controller can reduce the rigid and elastic vibrations of the vehicle and improve ride comfort.
The longitudinal non-uniformities in mass and stiffness distributions of railway vehicle carbodies, caused by doors, windows, and equipment compartments, significantly affect elastic vibrations and ride comfort. This paper establishes a vertical elastic vibration model based on the Euler–Bernoulli beam theory for variable cross-section carbodies, using piecewise uniform beam segments to represent actual cross-sectional properties. The transfer matrix method combined with the Newton–Raphson iteration is employed to solve natural frequencies and mode shapes. A hybrid active control strategy integrating secondary vertical electro-hydraulic actuators and distributed piezoelectric actuators is proposed. Based on a decentralised control architecture, a robust optimal controller is designed to suppress both rigid-body motions and the first two elastic modes. Simulation results at 250 km/h with a 20% centre-mass proportion show that the combined control reduces the vertical acceleration power spectral density (PSD) at the first vertical bending frequency to 5% of the passive suspension level, and to 35% at bounce and pitch frequencies. The Sperling ride index increases monotonically with speed, with the 20% mass proportion of the middle sub-beam yielding the best performance. The piezoelectric actuator voltage PSD reaches a peak of approximately 4000 V2·Hz−1 near the first bending frequency (0–15 Hz), demonstrating effective elastic vibration suppression, while the secondary actuator force PSD at the second bending frequency remains at around 103 N2·Hz−1, indicating limited contribution. The proposed variable cross-section beam model combined with hybrid control provides a theoretical foundation and engineering reference for lightweight design and active vibration reduction of high-speed trains.