Edouard Henry Demaldent

Dr. Edouard Henry Demaldent

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 September 2013 in International Journal for Numerical Methods in Engineering
Verified
Journal Article
Open access
PDF file
EDEdouard Henry Demaldent
Edouard Henry Demaldent
SIS. Imperiale
S. Imperiale
SUMMARY: This paper presents an original approach to design perfectly matched layers for anisotropic scalar wave equations. This approach is based, first, on the introduction of a modified wave equation and, second, on the formulation of general ‘perfectly matched’ transmission conditions for this equation. The stability of the transmission problem is discussed by way of the adaptation of a high frequency stability (necessary) condition, and we apply our approach to construct perfectly matched layer suited for any convex domain with straight boundaries. A new variational formulation of the problem, including a Lagrange multiplier at the interface between the physical and the absorbing domains, is then set, and numerical results are presented in 2D and 3D. These results show the efficiency of our approach when using constant damping coefficients combined with high order elements. Copyright © 2013 John Wiley & Sons, Ltd.

23 November 2024 in Ultrasonics
Verified
Journal Article
Open access
VDVincent Dorval
Vincent Dorval
NLNicolas Leymarie
Nicolas Leymarie
AIAlexandre Imperiale
Alexandre Imperiale
EDEdouard Henry Demaldent
Edouard Henry Demaldent
PLPierre-Emile Lhuillier
Pierre-Emile Lhuillier
Finite element computations offer ways to study the behavior of ultrasonic waves in polycrystals. In particular, the simulation of plane waves propagation through small representative elementary volumes of a microstructure allows estimating velocities and scattering-induced attenuation for an effective homogeneous material. Existing works on this topic have focused mainly on longitudinal waves. The approach presented here relies on generating periodic samples of microstructures in order to accommodate both longitudinal and shear waves. After some discussion on the parametrization of the simulations and the numerical errors, results are shown for several materials. These results are compared to an established theoretical attenuation model that has been adapted to use a fully analytical expression of the two-point correlation function for the polycrystals of interest, and to use velocities corresponding to different reference media. Promising comparisons are obtained for both longitudinal and shear waves when using more representative media, obtained through Hill averaging or a self-consistent approach. This illustrates how the numerical method can assist in developing and validating analytical models for elastic wave propagation in heterogeneous media.

19 April 2021 in Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems
Verified
Journal Article
Closed access
PDF file
OMOlivier Mesnil
Olivier Mesnil
ARArnaud Recoquillay
Arnaud Recoquillay
TDTom Druet
Tom Druet
VSValentin Serey
Valentin Serey
HHHuu Tinh Hoang
Huu Tinh Hoang
EDEdouard Henry Demaldent
Edouard Henry Demaldent
In guided wave structural health monitoring (GW-SHM), a strong need for reliable and fast simulation tools has been expressed throughout the literature to optimize SHM systems or demonstrate performance. Even though guided wave simulations can be conducted with most finite elements software packages, computational and hardware costs are always prohibitive for large simulation campaigns. A novel SHM module has been recently added to the civa software and relies on unassembled high-order finite elements to overcome these limitations. This article focuses on the thorough validation of civa for SHM to identify the limits of the models. After introducing the key elements of the civa SHM solution, a first validation is presented on a stainless steel pipe representative of the oil and gas industry. Second, validation is conducted on a composite panel with and without stiffener representative of some structures in the aerospace industry. Results show a good match between the experimental and simulated datasets, but only if the input parameters are fully determined before the simulations.

22 June 2016 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
AVAudrey Vigneron
Audrey Vigneron
EDEdouard Henry Demaldent
Edouard Henry Demaldent
MBMarc Bonnet
Marc Bonnet
We consider the solution, using boundary elements (BEs), of the surface integral equation (SIE) system arising in electromagnetic testing of conducting bodies, with an emphasis on situations, such that o(1) ≤ (ωε 0 /σ) 1/2 <; O(1) and L(ωσ μ 0 ) 1/2 = O(1), which includes in particular the case of eddy current (EC) testing and assuming Lω(ε 0 μ 0 ) 1/2 ≤ 2π, i.e., low-frequency conditions (L: diameter of conducting body). Earlier approaches for dielectric objects at low frequencies are not applicable in the present context. After showing that a simple normalization of the BE system significantly improves its conditioning, we propose a multi-step solution method based on block-successive over-relaxation iterations, which facilitates the use of direct solvers and converges within a few iterations for the considered range of physical parameters. This new treatment, albeit simple, allows to perform EC-type analyses using standard Maxwell SIE formulations, avoiding the adverse consequences of ill-conditioning for low frequencies and high conductivities. Its performance and limitations are studied on three numerical examples involving low frequencies and high conductivities.

12 April 2023 in Computers & Mathematics with Applications
Verified
Journal Article
Closed access
MBMarc Bonnet
Marc Bonnet
EDEdouard Henry Demaldent
Edouard Henry Demaldent

1 February 2022 in Insight - Non-Destructive Testing and Condition Monitoring
Verified
Journal Article
Closed access
TST Sollier
T Sollier
JDJ-M Decitre
J-M Decitre
AVA Vigneron
A Vigneron
EDEdouard Henry Demaldent
Edouard Henry Demaldent
The steam generator (SG) tubes of pressurised water reactors are prone to degradation and are periodically inspected using eddy current testing (ECT) techniques. SGs provide a safety barrier between the radioactive primary side and the non-radioactive secondary side. Historically, a major degradation issue was stress corrosion cracking of tubes made of alloy 600. In modern SGs, better resistance to stress corrosion cracking is observed with the replacement of alloy 600 by alloy 690. However, this alloy does not prevent tubes from wear at support locations or wear resulting from fretting with loose parts. Long-term operation of SGs also leads to non-volatile species accumulation in the secondary side of the SGs, mainly magnetite. Magnetite deposits may build up as a dense and solid material on top of the tubesheet (hard sludge) and also in the flow slots of tube support plates, therefore modifying the general flow pattern and velocity of the secondary fluid. This has detrimental effects on the safe operation of SGs. The clogging-up ratio of the flow slots therefore needs to be assessed. The development of an ECT simulation model to address tube wear and magnetite deposits in SGs is presented. This model is based on the CIVA NDT platform. A bobbin coil signal is simulated and its performance for tube wear and magnetite deposit evaluation is discussed.