Lithium manganese oxide (LMO), carbon nanotubes (CNTs), and graphene nanoplatelets (GNPs) were used to develop nanocomposites using a microwave‐assisted chemical precipitation method and characterized using various techniques. The process provides better control over morphological features and proficient choice of cost‐effective precursors. This research aims to increase the active surface area and the number of lithium‐ion (Li+) intercalation sites using the CNTs and GNPs in LMO to improve its electrochemical performance. The structural analysis shows that the average crystallite size is 50 nm without using any capping agent during the synthesis process, which is smaller when compared to pristine LMO. The electrochemical studies demonstrate that the incorporation of carbon nanostructures (CNTs and GNPs) boosts the rate capabilities and cyclic performance of LMO. The LMO‐CNTs and LMO‐GNPs have an excellent rate capability of 124 and 127 mAhg−1 at 0.1C, sustained at 115.6 and 118.5 mAhg−1 at 10C, respectively. Cycling efficiency is also improved, with LMO‐CNTs and LMO‐GNPs having an initial capacity of 124 and 127 mAhg−1 decreasing to 112 and 114 mAhg−1, respectively, after 50 cycles. Compared to pure LMO, the increased electrochemical performance of LMO nanocomposites is due to the introduction of carbon nanostructures (CNTs and GNPs).
A NASICON-based Na3V2(PO4)2F3 (NVPF) cathode material is reported herein as a potential symmetric cell electrode material. The symmetric cell was active from 0 to 3.5 V and showed a capacity of 85 mAh/g at 0.1 C. With cycling, the NVPF symmetric cell showed a very long and stable cycle life, having a capacity retention of 61% after 1000 cycles at 1 C. The diffusion coefficient calculated from cyclic voltammetry (CV) and the galvanostatic intermittent titration technique (GITT) was found to be ~10−9–10−11, suggesting a smooth diffusion of Na+ in the NVPF symmetric cell. The electrochemical impedance spectroscopy (EIS) carried out during cycling showed increases in bulk resistance, solid electrolyte interphase (SEI) resistance, and charge transfer resistance with the number of cycles, explaining the origin of capacity fade in the NVPF symmetric cell. Finally, the postmortem analysis of the symmetric cell after 1000 cycles at a 1 C rate indicated that the intercalation/de-intercalation of sodium into/from the host structure occurred without any major structural destabilization in both the cathode and anode. However, there was slight distortion in the cathode structure observed, which resulted in capacity loss of the symmetric cell. The promising electrochemical performance of NVPF in the symmetric cell makes it attractive for developing long-life and cost-effective batteries.
Cobalt-free LiNi0.5Mn1.5O4 (Lithium Nickel Manganese Oxide; LNMO) has garnered considerable interest as a cathode material due to its high working voltage, lower cost, and environmental friendliness. However, LNMO cathodes currently exhibit low cyclability and capacity deterioration, severely restricting their use on a broader scale. To this end, microwave-assisted chemical co-precipitation was used to produce spherical aggregated nanoparticles of LiNi0.5Mn1.5O4 (LNMO) coated with CeO2 (LNMO-Ce) and wrapped in graphene (LNMO-Ce-GO). Structural analysis demonstrates that the ceria coating along with the graphene wrapping prevents unwanted phases from forming and altering the morphology of the LNMO microspheres. LNMO-Ce-GO exhibits a discharge capacity of 131 mAhg-1 at the C/10 rate with a capacity retention of 98.6% after 100 cycles, compared to LNMO-Ce and bare LNMO samples that provide a capacity retention of 92% and 81% respectively. The ceria coating helps to suppress the adverse reactions at the electrode/electrolyte interface and reduce the Mn3+ dissolution due to the Jahn Teller effect, increasing cell cyclability. The graphene wrapping reduces material aggregation and provides conductive pathways that significantly improve the electrochemical performance of the LNMO cathode. This innovative material design strategy can be efficiently expanded to other classes of lithium-ion battery cathode materials to enhance their electrochemical performance.