Background: Pusher behavior after stroke is an important sequela that interferes with rehabilitation and independence in activities of daily living. As represented by visual or vestibular feedback, conventional methods require substantial assistance and time commitments, but have limited effectiveness. A recent case series suggests that prone posture may alleviate pusher behavior in patients with acute stroke. This study was conducted to retrospectively investigate the effects of prone posture maneuvers. Methods: This retrospective cross-sectional observational study was conducted in a stroke care unit at a university hospital. In total, 37 acute stroke cases presenting with pusher behavior were included from 787 eligible patients. Individuals with pusher behavior were conditioned with prone posturing for 10 min for 2 consecutive days, in addition to regular daily rehabilitation training. The Scale for Contraversive Pushing (SCP) values, Stroke Impairment Assessment Set (SIAS), and functional activities were assessed before, immediately after, and three days after the intervention. Results: The SCP value and the ability to roll over and sit balanced significantly improved compared with the baseline (p < 0.05) and persisted for 3 days after the intervention. Multiple regression analysis identified the SIAS motor score as a determinant of SCP changes. Conclusions: The prone posture maneuver promptly and consistently suppressed pusher behavior, particularly in patients with mild paresis, as indicated by SCP values in acute stroke cases. The uncontrolled, single-site, and retrospective features of the current study require further investigation.
Research Problem/aim: This study examined whether process recording increases self-focus, and whether this effect is moderated by self-compassion. Methods: Participants included 31 undergraduates in Tokyo. A pre-post-test design was used. Participants completed measures including self-focus and self-compassion before and after process recording. Participants were divided into high and low self-compassion groups. Findings: Overall, the mean rumination and reflection scores were 42.0 and 37.9, respectively, at pre-intervention. The low self-compassion group (n = 14) showed no significant changes in either subscale. The high self-compassion group (n = 17) showed a significant reduction in rumination. Conclusions: Overall, process recording does not influence self-focus, but does reduce rumination in those with high self-compassion. Enhancing self-compassion is needed before using process recording to prevent excessive rumination.
22 September 2026 in Frontiers in Rehabilitation Sciences
Introduction: Three-dimensional (3D) printers can produce customized assistive devices in occupational therapy; however, occupational therapists' perceptions and early usage following clinical introduction remain poorly understood. This study examined perceptions, perceived barriers and enabling conditions, and early usage patterns among occupational therapists following 3D printer introduction in a rehabilitation hospital with minimal formal implementation support. Methods: A 3D printer was installed in the occupational therapy department, allowing trial printing of existing design data after brief basic instruction was provided to one representative therapist; no structured staff training, CAD instruction, formal usage recommendations, workflow integration, or dedicated institutional support was provided. A self-administered study-specific, non-validated questionnaire assessed perceptions and selected implementation-related conditions before and six months after installation. Paired data from 43 participants (follow-up rate: 79.6%) were analyzed using the Wilcoxon signed-rank and McNemar tests. Results: After installation, selection of the barrier “there is no 3D printer in the workplace” significantly decreased (adjusted p < 0.001), whereas selection of institutional and operational constraints, including insufficient time (adjusted p < 0.001) and lack of medical reimbursement (adjusted p = 0.044), increased. Participants showed less agreement that using a 3D printer was difficult (adjusted p = 0.047), while agreement that 3D printing was useful in occupational therapy practice also decreased (adjusted p = 0.044). Although statistically significant, these changes were small in magnitude. No statistically significant change was observed in future intention to use 3D printing (adjusted p = 0.063). Available printer records did not permit quantitative assessment of individual use; use remained limited to exploratory printing of existing designs. Discussion: The introduction of a printer with minimal formal support was not accompanied by clear progression toward routine clinical use during the six-month observation period. These exploratory findings support further evaluation of structured education, technical assistance, workflow integration, and institutional arrangements, but do not establish their effectiveness or the causal effect of printer availability.