The advantages of labyrinth–honeycomb seals in turbomachines are widely increasing the usage of them. In this investigation, a numerical study has been done to simulate a labyrinth–honeycomb seal which is commonly used in rotor blade tip. Three-dimensional simulation has been performed by ANSYS-CFX. Simulation results show good agreements with experimental data. To have better understanding of flow behavior within the labyrinth–honeycomb seal, a set of sensitivity analyses on geometry parameters has been carried out. First, a smooth plate has been replaced with honeycomb and sensitivity analyses on geometry parameters have been performed. Then the sensitivity analyses of full model with honeycomb on the geometry parameters are done. The sensitivity analysis is done on: (i) gap between labyrinth and smooth plate or honeycomb, (ii) thickness of labyrinth fins, (iii) height of labyrinth fins, (iv) height of honeycomb cells (only for the honeycomb model), and (v) the effect of different fin thicknesses and their combinations. The results show that as the height of labyrinth rises, there would be much more vortices in the flow field and consequently the overall loss would increase and mass flow rate decreases. In addition, the width of labyrinth fins in small gaps has an important role on the mass flow rate. In small gaps, as the width of labyrinth fin decreases, the mass flow of smooth model decreases, but the mass flow of honeycomb model increases. Furthermore, in large gaps, the existence of smooth plate or honeycomb has minor influence on the flow field. In addition, larger cell depth of honeycombs leads to increasing loss. In this paper, a model with straightforward labyrinth is also investigated and the results have been compared with the stepped labyrinth.
This paper describes the procedure for developing a new airfoil family. This airfoil family applies to heavy-duty, industrial, and aero-derivative gas turbine compressors ranging from subsonic to transonic flow regimes. The airfoil family is generated by filling a database with optimized airfoil geometries. This database is structured in six dimensions, called design space parameters, including inlet Mach number, inlet flow angle, outlet flow angle, axial velocity density ratio, maximum thickness to chord ratio, and solidity. This six-dimensional space includes all compressor blades used in stationary gas turbine compressors. Each set of these design space parameters is related to an optimal geometry produced by the optimization system. The optimization system includes a parametrized airfoil generator, an accurate, fast blade-to-blade flow solver, and an evolutionary optimization algorithm. Airfoils of different stationary gas turbine compressor types are investigated to cover the required design space. Four hundred thirty airfoils, denoted as reference airfoils, are used to define design space borders. Comparing the newly optimized airfoils with reference airfoils revealed superior performance throughout the entire design space. They incorporate these optimized airfoils into a surrogate model, resulting in a fast, optimized airfoil generator (airfoil family). The transonic rotor of the existing multistage compressor has been redesigned according to the developed airfoil family. 3D computational fluid dynamics showed a 2% efficiency improvement for optimized blade row over the original design. Integrating this airfoil family and a streamline curvature code as part of a compressor design system is the main application of this advanced airfoil family.
This paper investigates the results of a frequency analysis performed on the blades of the last three compressor stages of two different gas turbines (Case A and B). The axial compressors in A and B have ten and eleven stages, respectively. The studied stages have identical number of blades in both compressors. However turbine B has higher number of upstream vanes before each rotating stage. Turbine B is actually a modified version of A with higher power output. The manufacturer provides acceptable ranges for several natural frequencies of blades of stage No.8 to 10 in case A. One of the purposes of this study is to figure out the logic behind the abovementioned ranges. FEM has been used in order to determine the natural frequencies of a single blade (for Campbell diagram) and bladed disk (for SAFE diagram). By surveying the results of the Campbell diagrams for blades of case A’s mentioned stages, it is concluded that the manufacturer has obtained the acceptable ranges by considering a 10% difference (at least) between single blade natural frequencies and excitation frequencies (upstream vane passage frequencies (VPF)). On the other hand, according to Campbell diagram, there is no resonance for these blades within the operational speed while SAFE diagrams show the existence of one resonance mode within the same range. The reason of this contradiction is found to be ignoring the disk stiffness effect on the blades frequencies. A same procedure was also followed to study the critical frequencies of the blades of the last three stages of turbine B’s compressor by SAFE diagrams. By checking the critical modes, it is concluded that these modes in case B are transferred to one or two modes higher in comparison to A which results in a much better vibrational behavior. This has been acquired by increasing the number of the upstream vanes. In addition, in case A’s compressor, the blades of the stage No.10 have been designed with far thicker airfoils (approximately 50%) when compared to stage No.8 and 9, even though their other dimensions are almost identical. But, this fault has been corrected in turbine B and the airfoils of all three stages almost have the same thickness. To sum up, although the design of mentioned blades in turbine B looks better and more logical than A, still a more precise look at its stages bladed disk SAFE diagrams reveals another issue. In some references there are some hints that low number of critical nodal diameter (veering region) might cause high level of blade vibration due to mistuning and this means that even in turbine B the design might not be optimal. A cure could be an increase or decrease in the number of upstream vanes in order to have a higher critical nodal diameter.