Custom-made dynamometry was shown to objectively analyze human muscle strength around the ankle joint with accuracy, easy portability and low costs. This paper describes the full method of calibration and measurement setup and the measurement procedure when capturing ankle torque for establishing reliability of a portable custom-built electronic dynamometer. After considering the load cell offset voltage, the pivotal position was determined, and calibration with loads followed. Linear regression was used for calculating the proportionality constant between torque and measured voltage. Digital means were used for data collection and processing. Four healthy consenting participants were enrolled in the study. Three consecutive maximum voluntary isometric contractions of five seconds each were registered for both feet during plantar flexion/dorsiflexion, and ankle torque was then calculated for three ankle inclinations. A calibration procedure resulted, comprising determination of the pivotal axis and pedal constant. Using the obtained data, a measurement procedure was proposed. Obtained contraction time graphs led to easier filtering of the results. When calculating the interclass correlation, the portable apparatus demonstrated to be reliable when measuring ankle torque. When a custom-made dynamometer was used for capturing ankle torque, accuracy of the method was assured by a rigorous calibration and measurement protocol elaboration.

Inactivity negatively influences general health, and sedentary behaviour is known to impact the musculoskeletal system. The aim of the study was to assess the impact of time spent in active and sedentary behaviour on foot muscle strength. In this observational study, we compared the acute effects of one day of prolonged sitting and one day of low-to-moderate level of activity on ankle torque in one group of eight healthy participants. Peak ankle torque was measured using a portable custom-made electronic dynamometer. Three consecutive maximal voluntary isometric contractions for bilateral plantar flexor and dorsiflexor muscles were captured at different moments in time. The average peak torque significant statistically decreased at 6 h (p = 0.019) in both static and active behaviours, with a higher average peak torque in the active behaviour (p < 0.001). Age, gender, body mass index and average steps did not have any significant influence on the average value of maximal voluntary isometric contraction. The more time participants maintained either static or active behaviour, the less force was observed during ankle torque testation. The static behaviour represented by the sitting position was associated with a higher reduction in the average peak ankle torque during a maximal voluntary isometric contraction when compared to the active behaviour.

The negative effects of SARS-CoV-2 infection on the musculoskeletal system include symptoms of fatigue and sarcopenia. The aim of this study is to assess the impact of COVID-19 on foot muscle strength and evaluate the reproducibility of peak ankle torque measurements in time by using a custom-made electronic dynamometer. In this observational cohort study, we compare two groups of four participants, one exposed to COVID-19 throughout measurements and one unexposed. Peak ankle torque was measured using a portable custom-made electronic dynamometer. Ankle plantar flexor and dorsiflexor muscle strength was captured for both feet at different ankle angles prior and post COVID-19. Average peak torque demonstrated no significant statistical differences between initial and final moment for both groups (p = 0.945). An increase of 4.8%, p = 0.746 was obtained in the group with COVID-19 and a decrease of 1.3%, p = 0.953 was obtained in the group without COVID-19. Multivariate analysis demonstrated no significant differences between the two groups (p = 0.797). There was a very good test–retest reproducibility between the measurements in initial and final moments (ICC = 0.78, p < 0.001). In conclusion, peak torque variability is similar in both COVID-19 and non-COVID-19 groups and the custom-made electronic dynamometer is a reproducible method for repetitive ankle peak torque measurements.

On MIT's OCW platform it can be found a 2011 released project of small radar system built for didactic purposes. This paper presents our iteration of the project., with some modifications. Firstly., we adapted the project in order to work with a laptop while supplied on USB and then made an automation for displacement of the antennas. Finally., some software modifications were made to enhance the processing speed.

This paper deals with implementation of an example of implementation of an algorithm into an FPGA. While some considerations about various possibilities (ASIC, ASIP, GPP) are made, here is demonstrated the ASIP version with implementation details. An economic version of a Reed-Solomon algorithm is demonstrated and further developments of the method are assessed.

3D interpolation of 2D antenna patterns is the method of choice in propagation estimation software, with few bibliographic references on the subject. In some applications there is a need for a pattern approximation of an antenna which is not polarized by one of the reference axes Ox or Oz (e.g. xPo1 antenna). Therefore, we have approached the waveguide approximation in Oz direction and the classical pattern in Ox direction, which prove to be not 1:1 equivalent. We show that the Oz representation is more suitable to obtain a pattern for inclined antennas and less adequate in the case of narrow beams.