In this paper, we propose a deformable-model-driven method to recognize the state of hanging clothes using three-dimensional (3D) observed data. For the task to pick up a specific part of the clothes, it is indispensable to obtain the 3D position and posture of the part. In order to robustly obtain such information from 3D observed data of the clothes, we take a deformable-model-driven approach[4], that recognizes the clothes state by comparing the observed data with candidate shapes which are predicted in advance. To carry out this approach despite large shape variation of the clothes, we propose a two-staged method. First, small number of representative 3D shapes are calculated through physical simulations of hanging the clothes. Then, after observing clothes, each representative shape is deformed so as to fit the observed 3D data better. The consistency between the adjusted shapes and the observed data is checked to select the correct state. Experimental results using actual observations have shown the good prospect of the proposed method.
In this paper, we propose a deformable model-driven method to obtain the 3D information necessary for handling clothes by manipulators from observation with stereo cameras. The task considered in this paper is to hold up a target part of clothes (e.g. one shoulder of a pullover) by the second manipulator, when the clothes are held in the air at any point by the first manipulator. First, the method calculates possible 3D shapes of the hanging clothes by simulating the clothes deformation. The 3D shape whose appearance gives the best fit with the observed images is selected as estimation of the current state. Then, based on the estimated shape, the 3D position and normal direction of the part where the second manipulator should hold are calculated. The results of preliminary experiments using actual two manipulators have shown the good potential of the proposed method.
1 September 2001 in Robotics and Autonomous Systems
Aiming at manipulating clothes, a model-driven method of estimating the state of hanging clothes is proposed. We suppose a system consisting of two manipulators and a camera. The task considered in this paper is to hold a pullover at its two shoulders by two manipulators respectively, as a first step for folding it. The proposed method estimates the state of the clothes held by one manipulator in a model-driven way and indicates the position to be held next by the other manipulator. First, the possible appearances of the pullover when it is held at one point are roughly predicted. Using discriminative features of the predicted appearances, the possible states for the observed appearance are selected. Each appearance of the possible state is partially deformed so as to get close to the observed appearance. The state whose appearance successfully approaches closest to the observed appearance is selected as the final decision. The point to be held next is determined according to the state. The results of preliminary experiments using actual images have shown the good potential of the proposed method.
This paper presents a biped locomotion control method for an exploration in unknown environment. It is still hard for humanoid robot to walk autonomously even an artificial construction such as a power plant which are overly arranged many stairs and pipes. In such an environment, the physical constraints with a collision avoidance, joint limitations and support region on the terrain, become dominant limitations for an exploration. Updating environmental information to biped walking pattern generator and controller, a biped walking on a complicated rough terrain can be achieved. The proposed method is validated through several dynamics simulations with the HRP-2 humanoid robot.
In this paper, we propose a strategy for a dual-arm robot to pick up a specific part of clothing with one hand while holding the item of clothing with its other hand. Due to the large deformability of clothing, the handling requirements differ from those required for the handling of rigid objects. In the case of holding a specific part of clothing, large deformation leads to a large variety of positions and orientations of the target part, requiring flexibility of both visual recognition and motion control. On the other hand, since the clothing can flexibly curve over the hand, a relatively large range of suitable actions is allowed for grasping the clothing. By considering these characteristics, the following three-stage strategy is proposed. First, the state of the clothing is recognized from visual observation of the clothing using a deformable-model [1]. Then, the theoretically optimal position and orientation of the hand for handling a specific part of the clothing is calculated based on the recognition results. Finally, the position and orientation of the hand is modified by considering the executable motion range of the dual arms. Preliminary experimental results using actual observations of a humanoid robot were used to validate the effectiveness of the proposed strategy.