Alain Alonso Ipiña

Dr. Alain Alonso Ipiña

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 May 2023 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Open access
PDF file
AAAlain Alonso
Alain Alonso
MLMariano Lázaro
Mariano Lázaro
DLDavid Lázaro
David Lázaro
DADaniel Alvear
Daniel Alvear
Polymers are widely employed in many areas, e.g. transport, packaging, electronic devices, etcetera. Among them, acrylonitrile–butadiene–styrene (ABS) is one of the most employed polymers due to its mechanical properties, its ease to mechanize and recyclability. Nevertheless, according to the fire properties, ABS behaviour is usually worse than other polymers, therefore, they have to be upgraded with flame retardant additives. To characterize the fire behaviour of a certain material is necessary to address several typology of tests, providing relevant properties such as thermal conductivity, flammability and heat released. However, researchers may not always be able to run all tests due to the lack of apparatus or samples. Therefore, it is necessary to seek bibliographic sources. As one might expect, for a given material, the property values should be similar, regardless of who performs the test. However, sometimes slightly different results are obtained, which may be due to different causes, such as differences in test set-up and in material composition/manufacture. These differences in properties may lead researcher to doubt which data to use. This paper presents the results of different types of tests using neat ABS polymer. Additionally, these results are compared with the data from literature, discussing the similarities/differences and offering a more comprehensive characterization of ABS. The laboratory techniques included in this work are: thermogravimetric analysis, differential scanning calorimetry, laser flash analysis, smoke density, cone calorimeter, fire propagation and flammability.

28 March 2019 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Closed access
PDF file
AAAlain Alonso
Alain Alonso
MUMariano Lázaro Urrutia
Mariano Lázaro Urrutia
PLPedro Lázaro
Pedro Lázaro
DLDavid Lazaro
David Lazaro
DADaniel Alvear
Daniel Alvear

23 February 2023 in Combustion Science and Technology
Verified
Journal Article
Closed access
AAAlain Alonso
Alain Alonso
DLDavid Lazaro
David Lazaro
MUMariano Lázaro Urrutia
Mariano Lázaro Urrutia
DADaniel Alvear
Daniel Alvear
Electrical cables must fulfil the Construction Product Regulation (CPR) by testing them according to EN 50,399. Nevertheless, an unfordable trial and error procedure could stem from the definition of new cables. To achieve a better understanding of fire behavior of cables, researchers have been using techniques such as bench and reduced scale tests and computational fire models result in a way to minimize trial and error process. The present work proposes the combination of bench scale tests, using cone calorimeters and fire simulation modeling. In a first step, the thermal characterization of the cable parts is carried out, and then, in a second step, use these data to model complete cable samples in cone calorimeter tests. The simulations are compared with experimental data of two already rated cables. This process is intended to discard erroneous configurations, which display in bench scale signs of misbehavior compared with rated cables. This would avoid the manufacture of the complete cable if the results do not fulfill the requirements, and eventually, proceed to its production and test in full-scale when they do. This work has been carried out with two multi-core cables and the materials they were made of, and the results showed: a) the inverse modeling process to characterize materials parts obtained a fairly accurate approach, with small inaccuracies in the peaks of the curves; b) two simulation models (simple and detailed) were able to reproduce in general terms the heat release rate curve; however, they released more energy than experimental tests and some discrepancies in the peaks were observed. Despite its simplicity, simple model obtained results fairly close to the experimental curves and took less time to simulate.

19 September 2019 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Closed access
PDF file
AAAlain Alonso
Alain Alonso
MUMariano Lázaro Urrutia
Mariano Lázaro Urrutia
PLPedro Lázaro
Pedro Lázaro
DLDavid Lazaro
David Lazaro
DADaniel Alvear
Daniel Alvear

29 April 2022 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Open access
PDF file
AAAlain Alonso
Alain Alonso
DLDavid Lázaro
David Lázaro
MLMariano Lázaro
Mariano Lázaro
DADaniel Alvear
Daniel Alvear
Thermal analysis has been proven to be an efficiently technique to analyse thermal decomposition reactions of different type of materials. This technique is widely used in different fields. Among them, fire science, where polymeric materials are very common, has a particular issue, being the combustion reactions recurrent on these analyses. Thermal analysis has different particularities depending on the studied material. For instance, polymeric materials could undergo different decomposition reactions that are highly dependent on definition of the thermal analysis boundary conditions. The International Confederation for Thermal Analysis and Calorimetry (ICTAC) (Vyazovkin et al. in Thermochim Acta 590:1–23, 2014) and standards (ISO 11358-1. Plastics—Thermogravimetry (TG) of polymers—Part 1: General principles. ISO. 2014; https://www.iso.org/standard/59710.html. Accessed 31 Jan 2022), (ISO 11357-1. Plastics — Differential scanning calorimetry (DSC) — Part 1: General principles. ISO. 2016; https://www.iso.org/standard/70024.html. Accessed 31 Jan 2022) stablish how to set-up these boundary conditions in the thermogravimetric (TG) and differential scanning calorimetry (DSC) standards. As far as initial amount of sample mass is concern, some discrepancies can be found between the standards. For instance, the standards suggest a sample mass between 10 and 100 mg for TG and between 2 and 40 mg for DSC, whereas the ICTAC recommendations suggests that the sample mass times the heating rate should not exceed 100 mg K·min−1 in thermo-oxidative decomposition analysis, which is equivalent to samples masses lower than 10 mg for heating rates of 10 K·min−1, or lower than 5 mg for heating rates of 20 K·min−1. This discrepancy may lead to obtain different results from the tests. Additionally, according to the thermal and thermo-oxidative decomposition of polymers, the ICTAC remarks the influence on the results of the sample thicknesses, carrier gas and heating rates, but it does not analyse the influence of self-heating as it does for the hazardous materials. This work presents a study of the self-heating influence in the thermal decomposition processes of two widely used polymers as poly methyl methacrylate (PMMA) and linear low-density polyethylene (LLDPE). TG/DSC tests are used to evaluate the thermal decomposition processes. Boundary conditions of the tests definition as sample mass, atmospheres, and heating rate are considered to evaluate its influence on the polymers self-heating effect on the thermal decomposition. It also includes how to check if TG/DSC tests follows the theoretical principles of the thermal analysis, or if the results are affected by the self-heating. In the present study, a series of 32 experimental tests has been performed, analysing 16 boundary conditions. These experimental tests allow evaluating the influence of selected boundary conditions on the mass loss, the heat flux, and the materials decomposition reactions. Additionally, we analyse the effect of the boundary conditions on the temperature of the sample. Results show the impact of each different boundary conditions of the self-heating effect, and its influence in the final thermal decomposition measured and they represent an aid to define the suitable conditions to perform TG/DSC test on PMMA and LLDPE, or similar polymer materials. This is done by the evaluation of the influence of the self-heating in parameters as the sample temperature lags defined in [1], the reactions heat fluxes, and the difference between the sample and the programmed temperature. It is also analysed the influence of the auto-ignition temperature in the thermal analysis. It is remarkable the PMMA auto-ignition temperature effect on the TG/DSC results. Finally, some useful recommendations have been defined.

29 November 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DLDavid Lazaro
David Lazaro
AAAlain Alonso
Alain Alonso
MUMariano Lázaro Urrutia
Mariano Lázaro Urrutia
DADaniel Alvear
Daniel Alvear
In a fire, the polymer combustion occurs when gaseous fuels react with oxygen. The heating of a material could force the release of gaseous fuels during thermal decomposition and pyrolysis. The rate of pyrolysis to define the gaseous fuels is usually interpreted by means of the Arrhenius expression and a reaction model expression, which are characterized by an activation energy, a pre-exponential factor, and a reaction order value. Many methods are available for determining kinetic parameters from thermogravimetric experimental data. However, the most challenging issue is achieving an adequate balance between accuracy and simplicity. This work proposes a direct method for determining the kinetic parameters with only a thermogravimetric experiment at a single heating rate. The method was validated with six polymers, and the results were compared with those from similar procedures, such as the Lyon method and generalized direct method. The results achieved using the simpler approach of the proposed method show a high level of accuracy.