Maneuverability, which is closely related to operational performance and safety, is one of the important hydrodynamic properties of an underwater vehicle (UV), and its accurate prediction is essential for preliminary design. The purpose of this study is to analyze the turning ability of a UV while rising or submerging; the computational fluid dynamics (CFD) method was used to numerically predict the six-DOF self-propelled maneuvers of submarine model BB2, including steady turning maneuvers and space spiral maneuvers. In this study, the overset mesh method was used to deal with multi-body motion, the body force method was used to describe the thrust distribution of the propeller at the model scale, and the numerical prediction also included the dynamic deflection of the control planes, where the command was issued by the autopilot. Then, this study used the published model test results of the tank to verify the effectiveness of the CFD prediction of steady turning maneuvers, and the prediction of space spiral maneuvers was carried out on this basis. The numerical results show that the turning motion has a great influence on the depth and pitch attitude of the submarine, and a “stern heavier” phenomenon occurs to a submarine after steering. The underwater turning of a submarine can not only reduce the speed to brake but also limit the dangerous depth. The conclusion is of certain reference significance for submarine emergency maneuvers.

Recently, the NURBS technique has been widely used in the 3D design software for ships. However, in most research, the NURBS technique is only applied to the mathematical representation of hull curves and surfaces, and the parametric deformation of hull surfaces based on geometric feature parameters is less understood. The aims of this paper are to establish the parametric design process of hull surfaces through the classification of geometric feature parameters and the design of feature curves, apply the NURBS technique to the parametric geometric modeling of hull curves and surfaces, and finally achieve the parametric deformation of hull surfaces driven by geometric feature parameters and develop the parametric deformation software. Taking the Series 60 ship as an example, we first analyze the hull geometric features and parameters, then design the longitudinal feature curves and cross-section curves based on the NURBS technique and establish the correlation between them, and finally generate the smooth hull surface by the skinning technique to achieve the parametric geometric deformation of the Series 60 ship. The research in this paper shows that the smoothness of the surfaces generated by the NURBS-based parametric design method is good. Additionally, the extracted feature parameters have a clear geometric meaning and can automatically generate hull forms to meet the design requirements quickly and effectively, which has some practical engineering value.

While navigating at sea, ships are influenced by various factors, including wind, waves, and currents, which can result in heave motion that significantly impacts operations and potentially leads to accidents. Accurate forecasting of ship heaving is essential to guarantee the safety of maritime navigation. Consequently, this paper proposes a hybrid neural network method that combines Convolutional Neural Networks (CNNs), Bidirectional Long Short-Term Memory Networks (BiLSTMs), and an Attention Mechanism to predict the heaving motion of ships in moderate to complex sea conditions. The data feature extraction ability of CNNs, the temporal analysis capabilities of BiLSTMs, and the dynamic adjustment function of Attention on feature weights were comprehensively utilized to predict a ship’s heave motion. Simulations of a standard container ship’s motion time series under complex sea state conditions were carried out. The model training and validation results indicate that, under sea conditions 4, 5, and 6, the CNN-BiLSTM-Attention method demonstrated significant improvements in MAPE, APE, and RMSE when compared to the traditional LSTM, Attention, and LSTM-Attention methods. The CNN-BiLSTM-Attention method could enhance the accuracy of the prediction. Heave displacement, pitch displacement, pitch velocity, pitch acceleration, and incoming wave height were chosen as key input features. Sensitivity analysis was conducted to optimize the prediction performance of the CNN-BiLSTM-Attention hybrid neural network method, resulting in a significant improvement in MAPE and enhancing the accuracy of ship motion prediction. The research presented in this paper establishes a foundation for future studies on ship motion prediction.

Hull form optimization becomes prone to the curse of dimensionality as the number of design variables increases. The traditional sensitivity analysis method requires massive computational fluid dynamics (CFD) computations and analyzing the effects of all variables on the output; thus, it is extremely time-consuming. Considering this, the development of a rapid and effective dimensionality reduction method is particularly important. The Karhunen–Loève (K–L) transform method projects data from a high-dimensional space onto a low-dimensional space in the direction of the eigenvectors corresponding to large-variance eigenvalues. It extracts the principal components that represent the hull offset information to represent the hull geometric characteristics by analyzing the relationship between the variables in the sample offset matrix. The geometric information matrices of new hull forms can be rapidly reconstructed from the principal components. Compared with direct optimization methods, fewer variables are used to control the deformation of the hull form from the perspective of geometric deformation, avoid a large number of CFD calculations, and improve the efficiency of optimization. This study examined the relevant K–L matrix solution methods and the corresponding hull form reconstruction methods and proposed eigenvalue-based hull form reconstruction equations. The K–L transform method was combined with a previously developed multidisciplinary platform for a comprehensive optimization of ship hydrodynamic performance for hull form optimization, and its effectiveness was verified by using it to optimize DTMB 5415. The results showed that the K–L transform–based dimensionality reduction method significantly reduces the time consumption of optimization while maintaining an acceptable optimization performance.