Alcohols extensively used in internal combustion engines are important renewable and sustainable energy resources from environmental and economical perspectives. Besides, bio production of alcohols decreases consumption of fossil-based fuels. Although there are many studies with regards to the use of lower alcohols such as methanol and ethanol in internal combustion engines, there are a limited number of investigations with higher alcohols. Higher alcohols such as propanol, n-butanol, and 1-pentanol are part of the next generation of biofuels, given they provide better fuel properties than lower alcohols. Biodiesel–higher alcohol blends can be used in diesel engines without any engine modification but need to be tested under various engine conditions with long periods in order to evaluate their impacts on engine performance and environmental pollutants. The objective of this study was to evaluate the effect of using propanol, n-butanol, and 1-pentanol in waste oil methyl ester (B100) on engine performance and exhaust emissions of a diesel engine running at different loads (0, 3, 6, and 9 kW) with a fixed engine speed (1800 rpm). Test fuel blends were prepared by adding propanol, n-butanol, and 1-pentanol (10 vol.%) into waste oil methyl ester to achieve blends of B90Pr10, B90nB10, and B90Pn10, respectively. According to engine performance and exhaust emissions results, the addition of propanol, n-butanol, and 1-pentanol to B100 had the effect of increasing brake specific fuel consumption and exhaust gas temperatures. The brake thermal efficiency (BTE) decreased for B90Pr10 and B90nB10, while B90Pn10 showed a slight increase in BTE as compared with B100. When compared with B100, B90Pr10, B90nB10, and B90Pn10 decreased carbon monoxide emissions at lower loads while it increased slightly at 9 kW load. The decrement in oxides of nitrogen emission was observed at whole loads for B90Pr10, B90nB10, and B90Pn10 compared with B100. When considering all loads, B90Pn10 presented the best mean hydrocarbon emission with a reduction of 45.41%. Copyright © 2016 John Wiley & Sons, Ltd.

A review of the literature pertaining to hypergolic fuel systems, particularly using hydrazine or its derivatives and hydrogen peroxide, has been conducted. It has been shown that a large effort has been made towards minimizing the risks involved with the use of a toxic propellant such as the hydrazine. Substitution of hydrazines for nontoxic propellant formulations such as the use of high purity hydrogen peroxide with various types of fuels is one of the major areas of study for future hypergolic propellants. A series of criteria for future hypergolic propellants has been recommended, including low toxicity, wide temperature range applicability, short ignition delay, high specific impulse or density specific impulse, and storability at room temperature.

Higher alcohols can be included as a third component in biodiesel-diesel mixtures to improve fuel properties and reduce emissions. Determining the optimum concentrations of these fuels according to the purpose of engine use is important both environmentally and economically. In this study, eight different concentrations of diesel (D), waste oil derived biodiesel (WOB), and 1-pentanol (P) ternary mixtures were determined by the design of experimental method (DOE). In order to determine the engine performance and exhaust emission parameters of these fuels, they were tested on a diesel engine with a constant load of 6 kW and a constant engine speed of 1800 rpm. Using the test results obtained, a full quadratic mathematical model with a 95% confidence level was created using the Response Surface Method (RSM) to predict five different output parameters (BSFC, BTE, CO, HC, and NO_x) according to the fuel mixture ratios. The R² accuracy values of the outputs were found at the reliability level. According to the criteria that BTE will be maximum and BSFC, CO, HC, and NO_x emissions will be minimum, the optimization determined that the fuel mixture 79.09% D-8.33% WOB-12.58% P concentration (DWOBP_opt) will produce the desired result. A low prediction error was obtained with the confirmation test. As a result, it is concluded that the optimized fuel can be an alternative to the commonly accepted B7 blend and can be used safely in diesel engines.

There are a number of emissions produced by internal combustion engines that are regulated to limit atmospheric pollution. However, it is equally important for both environmental and human health to also monitor and control polycyclic aromatic hydrocarbons (PAHs). Using high-carbon alcohols with straight-chain structures, such as n-propanol (Pro), n-butanol (Bu) and n-pentanol (Pen), together with diesel fuel (D), can be a way to reduce these harmful pollutants. In this study, nine different test fuels were created by mixing each higher alcohol with diesel fuel at 5%, 20% and 30% mixing ratios. In order to compare the effects of these test fuels on regulated pollutants and PAH compounds, fuel blends were evaluated in a diesel engine at partial loads and at a constant speed. Regulated emissions were measured using a standard 5-gas analyzer, and PAHs were detected and quantified using rigorous analytical chemistry methods, such as gas chromatography–mass spectrometry (GC–MS). While higher carbon monoxide (CO) and hydrocarbon (HC) pollutants were emitted by the binary blends due to their high oxygen content and latent heat of evaporation (LHE), a decrease in nitrogen oxides (NO_x) emissions between 4.98% and 20.08% was observed depending on the alcohol concentration. With the exception of the 20% n-pentanol mixture, PAH concentrations in the exhaust gas were significantly reduced in other binary blends. The 35% n-butanol mixture stood out in reducing total PAHs by 80.98%. In toxicity reduction, the 20% n-propanol mixture was the most effective with a decrease of 91.23% in toxicity. Overall, higher alcohols have been shown to be effective additives not only in reducing overall PAH emissions and toxicity, but also in reducing high-ring and heavier PAHs, which are more carcinogenic and cause a greater risk to engine lifedue to wet stacking under cold starting or low-load conditions.